User manual SHARP AR-FN2 OPERATION MANUAL

[. . . ] NOTE: The AR-FN2 finisher is optional equipment for the AR-280/AR-285/ AR-335 Copiers. This manual describes only the features of the AR-FN2 finisher. For general information on the copier features, see the Operation Manual of the copiers. AB series (metric) and inch series references Both specifications are quoted where applicable. q The inch series specifications are quoted in brackets. [. . . ] When the document glass is used for copying, copies will be grouped at the default setting. In the STAPLE SORT mode, only A4 (8-1/2" x 11") paper can be used. q SORT mode 123 2 1 3 Each set of copies will be sequentially delivered to the offset tray or the top tray as selected. 123 123 GROUP mode 111 2 1 3 222 333 3 2 1 All copies of the same original will be grouped in the offset tray or the top tray. STAPLE SORT mode 2 1 3 3 2 1 3 2 1 Collated sets of copies will be stapled and delivered to the offset tray. q See next page for details. 3 Staple sort The STAPLE SORT mode staples A4 (8-1/2" x 11") size copies. Stapled sets cannot be delivered to the top tray. NOTE: Different size originals cannot be copied onto copy paper of their respective sizes in the STAPLE SORT mode. Only A4 (8-1/2" x 11") size paper can be selected in the STAPLE SORT mode. Using the SPF/RADF AR-280 Stapling position 1 Set the originals in the document feeder tray. q If the number of copies in one set is more than 30, the copies will not be stapled. If the orientation of the originals does not match that of the copy paper, the images of the originals will be rotated. The stapling position in this case is shown below. AR-280 AR-285/AR-335 q AR-285/AR-335 Stapling position q If originals in the landscape orientation are copied, the copies will be stapled at an improper position. AR-280 AR-285/AR-335 2 AUTO EXPOSURE READY TO COPY. (DOCUMENT FEEDER MODE) OUTPUT TOP TRAY OFFSET TRAY AUTO EXPOSURE SORT AUTO A4 PAPER SELECT STAPLE SORT OK Press the OUTPUT key. 3 Press the "STAPLE SORT" key on the touch panel. GROUP 100% COPY RATIO 4 READY TO COPY. (DOCUMENT FEEDER MODE) OUTPUT TOP TRAY OFFSET TRAY AUTO EXPOSURE SORT AUTO A4 PAPER SELECT STAPLE SORT OK 4 Press the "OK" key. GROUP 100% COPY RATIO 1 4 7 AUDIT CLEAR 2 5 8 0 3 6 INTERRUPT 5 Set the number of copies. q If A4 (8-1/2" x 11") paper has not been selected, press the "PAPER SELECT" key and select a paper tray containing A4 (8-1/2" x 11") paper. 9 PROGRAM CLEAR C P CLEAR ALL INTERRUPT CA START CLEAR 6 Press the START ( q ) key. When copying of one set is completed, the copies will be automatically stapled and delivered to the offset tray. C 5 Using the document glass Stapling position 1 Set the original on the document glass with the corner to be stapled to the upper right. q q q Copy from the last page to the first page. If the number of copies in one set is more than 30, the copies will not be stapled. If the orientation of the original does not match that of the copy paper, the image of the original will be rotated. The stapling position in this case is shown below. q If originals in the landscape orientation are copied, the copies will be stapled at an improper position. 2 AUTO EXPOSURE READY TO COPY. OUTPUT TOP TRAY OFFSET TRAY AUTO EXPOSURE SORT AUTO A4 PAPER SELECT STAPLE SORT OK Press the OUTPUT key. 3 Press the "STAPLE SORT" key on the touch panel. GROUP 100% COPY RATIO READY TO COPY. OUTPUT TOP TRAY OFFSET TRAY AUTO EXPOSURE SORT AUTO A4 PAPER SELECT STAPLE SORT OK 4 Press the "OK" key. GROUP 100% COPY RATIO 6 1 4 7 AUDIT CLEAR 2 5 8 0 3 6 INTERRUPT 5 Set the number of copies. q If A4 (8-1/2" x 11") paper is not selected, press the "PAPER SELECT" key and select a paper tray containing A4 (8-1/2" x 11") paper. 9 PROGRAM CLEAR C P CLEAR ALL INTERRUPT CA START CLEAR 6 7 8 Press the START ( ) key. Replace the finished original with the next original after the START ( ) key indicator lights up, and then press the START ( ) key. Repeat this step until all originals have been scanned. C After all originals are scanned, press the "READ-END" key on the touch panel. q PLACE NEXT ORIGINAL. READ-END AUTO EXPOSURE AUTO A4 PAPER SELECT Copying will start and each set of copies will be automatically stapled and delivered to the offset tray. 100% COPY RATIO 7 Staple cartridge replacement The message "ADD STAPLES. " will appear when the staple cartridge is empty. Replace the staple cartridge as follows: 1 Open the stapler cover. 2 Lift the green release lever and remove the staple cartridge from the stapler. q A few staples will be left in the cartridge. Remove and discard them. 3 Insert a new sheet of paper (8-1/2" x 11" or A4 size) to the tray as shown in the picture to make the stapler work properly. 4 Check that the first staple in the new cartridge is at the tip of the cartridge. q If the first staple is not at the tip, pull it to the tip. If any staples are protruding past the cartridge tip, tear them off at the STAPLE TEAR line and align the first staple with the tip. A cartridge holds 5, 000 staples. q STAPLE TEAR line 5 6 8 Push the new staple cartridge in until it clicks in place. Close the stapler cover. q The stapler will strike three times without stapling and feed staples automatically. [. . . ] to 34 lbs. ) Offset tray: 56 to 128 g/m2 (15 lbs. to 34 lbs. ) For paper weighing more than 105 g/m2 (28 lbs. ), A4 (8-1/2" x 11") is the maximum size. 15 mm for A4 (61/64 inch for 8-1/2" x 11") A4 (8-1/2" x 11") Stapling capacity 30 sheets (80 g/m2 (21 lbs. )) Power supply Weight Dimensions Drawn from the copier Approx. 22 kg (49 lbs. ) 457 mm (W) x 518 mm (D) x 820 mm (H) (18"(W) x 20-13/32"(D) x 32-19/64"(H)) Specifications are subject to change for improvement without notice. Key operator program The following key operator program can be used when the optional finisher (AR-FN2) is installed. [. . . ]