User manual SHARP AR-FX13

[. . . ] MODEL AR-FX13 FACSIMILE EXPANSION KIT OPERATION MANUAL Page · INSTALLATION · INITIAL SETTINGS · CHOOSING SUITABLE MEDIA · HOW TO USE THE FAX FUNCTION · SPECIAL FUNCTIONS · TROUBLESHOOTING · APPENDIX 11 13 50 52 67 85 92 IMPORTANT NOTICE FOR AUSTRALIA AND NEW ZEALAND USERS Your fax machine and the telephone system WARNING NOTICE: NO calls can be made to or from this fax during a mains power failure. WARNING -- Australian Communications and Media Authority (ACMA) regulations state that no unauthorised changes or modifications to this equipment are permitted. Note: Complies with the following standards, AS/NZS 60950. 1 AS/ACIF S002, NZ TELECOM and CISPR 22 These limits are designed to provide reasonable protection against interference in an installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause interference. [. . . ] (The factory default setting for the original size is "8. 5x11". ) If the displayed size is not correct, press the [CLEAR ALL] key ( ) to stop operation and then change the original size setting. (See "ORIGINAL SIZE" (p. 54)) When faxing from the document glass, if the size of the original is different from the specified size, part of the image may be cut off. 4 6 Note When using the document glass, do not set original(s) in the RSPF. If you have more than one original to read into memory, place the next page, and press the [START] key ( ) to read each page. Go to step 7 after the last page has been scanned. 4 If needed, set the original size (p. 54), resolution (p. 55), and contrast (p. 55). Continue with the "DIALING AND TRANSMITTING" (p. 59) section. 7 Press the [#] key. Transmission begins. 53 OPTIONAL TRANSMISSION SETTINGS There are several transmission settings that you can make before dialing and transmitting an original. ORIGINAL SIZE The original size can be set to "A4", "8. 5x11", or "8. 5x14". The setting is only effective for one transmission. If desired, you can set a fixed original size that remains in effect for all transmissions. 1 Press the [MENU] key. 5 Press the [ENTER] key. 2 Press the [ ] key ( ) or [ ] key ( ) until "4:USER PROGRAM" appears, and then press the [ENTER] key. 6 Press the [MENU] key. Press the [MENU] key to exit. Selection "4:USER PROGRAM" 3 Press the [ ] key ( ) or [ ] key ( ) until "1:DOC. GLASS SIZE" appears, and then press the [ENTER] key. Selection "1:DOC. GLASS SIZE" To set a fixed original size for all transmissions: Press the [ ] key ( ) or [ ] key ( ) to select "2:FIXED DOC. SIZE". Note To temporarily change the original size setting when faxing from the document glass, use the "1: DOC. To change the permanent original size setting, use the "2: FIXED DOC. SIZE" setting. 4 Press the [ ] key ( ) or [ to select the original size. ] key ( ) The selections are as follows: 1:A4 2:8. 5x11 3:8. 5x14 54 HOW TO USE THE FAX FUNCTION RESOLUTION To do this, press the [RESOLUTION] key one or more times until the desired resolution settings appear in the display, and then press the [ENTER] key. Your fax has five resolution settings: · STANDARD Use STANDARD for ordinary originals. This setting gives you the fastest transmission. · FINE Use FINE for improved reproduction, especially with originals containing small letters or fine drawings. · SUPER FINE Use SUPER FINE when you need the highest quality of reproduction. · FINE (HALF TONE) Use FINE (HALF TONE) if your original is a photograph or has gradations of color (such as a color original). This setting will produce a clearer image than Fine used alone. FINE (HALF TONE) Use S. FINE (HALF TONE) if your original is a photograph or has gradations of color (such as a color original). This setting will produce a clearer image than Super fine used alone. In order to transmit with FINE or SUPER FINE resolution, the receiving fax machine must also have that resolution. If it doesn't, the next best available setting will be used. If you do not change the setting, the resolution set using the RESOLUTION PRIORITY (p. 37) setting will be automatically selected. 4 CONTRAST The fax automatically controls the contrast, but you can also control it manually. To do this, press the [CONTRAST] key one or more times until the desired contrast settings appear in the display, and then press the [ENTER] key. [. . . ] 64 Sending originals - Dialing and transmitting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59 - Manual sending. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66 - Optional transmission settings . . . . . . . . . . . . . . . . . . . . . . . . . 54 - Setting the original . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]