User manual SHARP AY/AE-XM18BE

[. . . ] E-4 · BASIC OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E-6 · ADJUSTING THE AIR FLOW DIRECTION . . E-8 · TIMER OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E-9 · ONE-HOUR OFF TIMER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] » Make sure there is no curtain or other object between the remote control and the unit. » The remote control can send signals from up to 7 metres away. E-4 CAUTION » Do not allow the signal receiver window to receive strong direct sunlight, since it can adversely affect its operation. If the signal receiver window is exposed to direct sunlight, close a curtain to block the light. » Using a fluorescent lamp with a quick starter in the same room may interfere with transmission of the signal. » The unit can be affected by signals transmitted from the remote control of a television, VCR or other equipment used in the same room. » Do not leave the remote control in direct sunlight or near a heater. Also, protect the unit and remote control from moisture and shock which can discolour or damage them. SETTING THE CURRENT CLOCK TIME There are two clock modes: 12hour mode and 24-hour mode. Example: 5 o'clock in the afternoon Clock Display 12-hour mode PM 5:00 24-hour mode 17:00 MODE FAN 1 3 1 To set to the 12-hour mode, press the CLOCK button once in the first step. To set to the 24-hour mode, press the CLOCK button twice in the first step. SWING SET/C 2 3 + - Å| Å{ Å{ Å| 2 Press the TIME ADVANCE or REVERSE button to set the current time. » Keep the button pressed to advance or reverse the time display quickly. » The colon (:) blinks to indicate that the clock is functioning. NOTE: » The current time cannot be set when the timer is operating. E-5 ENGLISH BASIC OPERATION 1 Press the MODE button to select the operation mode. AUTO HEAT COOL DRY FAN ONLY AM 1H P @ , FAN SWING SET/C + - 2 Press the ON/OFF button to start operation. Press the TIME ADVANCE or REVERSE button to set the desired time. (The time can be set in 10-minute increments. ) Point the remote control at the signal receiver window on the unit and press the TIMER SET (SET/C) button. » The yellow TIMER lamp ( ) on the unit will light. » The unit will generate a beep when it receives the signal. » The unit will turn on prior to the set time to allow the room to reach the desired temperature by the programmed time. (Awaking function) 1H MODE FAN 4 Select the operation condition. 3 1 2 SWING SET/C + - COMBINED USE OF ON AND OFF TIMERS You can use the ON and OFF timers in combination. Example: To stop operation at 11:00 p. m. and resume operation (with the same mode and temperature settings) to bring the room temperature to the desired level by 7:00 a. m. AM 1 2 Set the TIMER OFF to 11:00 p. m. Set the TIMER ON to 7:00 a. m. PM The arrow ( or ) between the TIMER ON indicator and the TIMER OFF indicator shows which timer will activate first. NOTES: »You cannot programme the TIMER ON and TIMER OFF to operate the unit at different temperatures or other settings. » Either timer can be programmed to activate prior the other. E-10 ONE-HOUR OFF TIMER When the ONE-HOUR OFF TIMER is set, the unit will stop operating after one hour. 1H 2 NOTE: » The ONE-HOUR OFF TIMER operation has priority over TIMER ON and TIMER OFF operations. AUXILIARY MODE Use this mode when the remote control is not available. TO TURN ON Lift the front panel of the indoor unit and press the AUX. » The red OPERATION lamp ( ) on the unit will light up and the unit will start operating in the AUTO mode. [. . . ] (the compressor runs continuously. ) , , , , , , , , , , , , , , TEST RUN AUX TO TURN OFF Press the AUX. » Setting the temperature lower than necessary during cooling operation will result in increased power consumption. » Blocking direct sunlight during cooling operation will reduce power consumption. » Close the windows and doors during cooling opeation and heating operation . BLOCK DIRECT SUNLIGHT AND PREVENT DRAFTS SET PROPER AIR FLOW DIRECTION TO OBTAIN THE BEST AIR CIRCULATION KEEP FILTERS CLEAN TO ENSURE THE MOST EFFICIENT OPERATION MAKE MOST OF THE TIMER OFF FUNCTION DISCONNECT THE POWER CORD WHEN THE UNIT IS NOT USED FOR AN EXTENDED PERIOD OF TIME » The indoor unit still consumes a small amount of power when it is not operating. E-13 ENGLISH PREHEATING FUNCTION MAINTENANCE Be sure to disconnect the power cord from the wall outlet or turn off the circuit breaker before performing any maintenance. CLEANING THE FILTERS The air filters should be cleaned every two weeks. 1 TURN OFF THE UNIT 2 REMOVE THE FILTERS 1 2 3 1 Open the front panel. [. . . ]