User manual SHARP AY-XP09DR-NC

[. . . ] AY-XP09DR-NC OPERATION MANUAL · Uses ozone layer friendly refrigerant R410A. INDOOR UNIT OUTDOOR UNIT AY-XP09DR-NC AE-X09DR-N ENGLISH SPLIT TYPE ROOM AIR CONDITIONER ENGLISH CONTENTS · PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E-1 · PART NAMES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E-3 · SETTING DEODORANT DUST COLLECTING FILTER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E-5 · USING THE REMOTE CONTROL . . . . . . . . . . . E-6 · BASIC OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] TIME 2 Press the set theADVANCE or REVERSE button to current time. · Keep the button pressed to advance or reverse the time display quickly. CLEAN FAN SWING SET/C 3 Press the SET/C button. indicate that the · The colon (:) blinks to clock is functioning. NOTE: · The current time cannot be set when the timer is operating. E-7 ENGLISH BASIC OPERATION 1 Press the MODE button to select the operation mode. AUTO HEAT COOL DRY 2 2 5 3 DISPLAY Press the ON/OFF button to start operation. · The red OPERATION lamp ( will light. button to set the desired temperature. · In the AUTO and DRY mode, the temperature can be changed in 1°C increments within the range of 2°C higher to 2°C lower from the temperature automatically determined by the air conditioner. · In the COOL and HEAT modes, the temperature can be set within the range of 18 to 32°C (Example: 1°C higher) 1 MODE 1h C (Example: 2°C lower) CLEAN FAN SWING SET/C 4 C 4 Press the FAN button to set the desired fan speed. AUTO SOFT LOW HIGH · In the DRY mode, the fan speed is preset to AUTO and cannot be changed. 5 To turn off the unit, press the ON/OFF button again. · The red OPERATION lamp ( will turn off. ) on the unit TIPS ABOUT AUTO MODE In the AUTO mode, the temperature setting and mode are automatically selected according to the room temperature and outdoor temperature when the unit is turned on. Modes and Temperature Settings During operation, if the outdoor temperature changes, the temperature settings will automatically slide as shown in the chart. 29 21 (¡C) 0 10 18 Cool (24¡C) 28 34 temp. (¡C) outdoor Cool Cool (25¡C) (26¡C) Heat Heat (24¡C) (23¡C) Dry ( Room Temp. ) -2¡C Heat (22¡C) indoor temp. the figures in ( ) are temperature settings E-8 TIPS ABOUT INDICATOR PANEL The indicator panel will change each time you press the DISPLAY button in the following manner. The room temperature is displayed. temperature Indiactor Room Temp. Lamp DISPLAY temperature Indiactor Outdoor Temp. Lamp The outdoor temperature is displayed. No display. NOTES: · The displayed temperatures are rough estimates and may vary from the actual temperatures. · Temperature display ranges is displayed when less than 0°C and when higher Room temperature: 0°C ~ 40°C ( than 40°C) Outdoor temperature: -9°C ~ 45°C ( is displayed when less than -9°C and when higher than 45°C) is displayed during the first 60 seconds of operation while the temperatures are being · detected. · Only the room temperature can be displayed for 5 seconds when the unit is not in operation. PROGRESSIVE AIRFLOW Press the Progressive Air Flow button during cooling or dry operation when you do not want to feel cold air. Condensation may form on the louvres. E-10 10°C OPERATION Heating operation with 10°C set temperature will be performed. AM 1 Press the MODE button and select HEAT mode. 2 Press the ON/OFF button to start HEAT operation. 3 Pressremote control will display 10°C . · The TO CANCEL Press the 10°C button again. · 10°C operation will also be cancelled when the operation mode is changed, or when the unit is turned off. ENGLISH DISPLAY MODE 1h CLEAN FAN SWING SET/C 1 NOTE: · 10°C operation will not be available with heating operation automatically selected by AUTO mode. FULL POWER OPERATION In this operation, the air conditioner works at maximum power to makes the room cool or warm so rapidly that you can use it just after you come home. FULL 1 To activate the button POWER operation, press the FULL POWER during operation. · The remote control will display . · The temperature display will go off. AM TO CANCEL Press the FULL POWER button again. · FULL POWER operation will also be cancelled when the operation mode is changed, or when the unit is turned off. DISPLAY 1 NOTE: · You can not set the temperature and fan speed during the FULL POWER operation. E-11 ONE-HOUR OFF TIMER When the ONE-HOUR OFF TIMER is set, the unit will stop operating after one hour. 1 Press the ONE-HOUR OFF TIMER button. · The remote control displays " ". · The orange TIMER lamp ( ) on the unit will light up. · The unit will stop operating after one hour. TO CANCEL Press the TIMER CANCEL (SET/C) button. MODE 1h 1 · The orange TIMER lamp ( ) on the unit will turn off. Or, turn the unit off by pressing the ON/OFF button. · The red OPERATION lamp ( ) and the orange TIMER lamp ( ) on the unit will turn off. CLEAN FAN NOTES: · The ONE-HOUR OFF TIMER operation has priority over TIMER ON and TIMER OFF operations. · When the ONE-HOUR OFF TIMER is set while the unit is not operating, the unit will operate for an hour with the formerly set condition. [. . . ] · Condensation may form on the air outlet if the unit operates continuously in the COOL or DRY mode when humidity is over 80 percent. 20°C D. B. - WHEN POWER FAILURE OCCURS This air conditioner has a memory function to store settings when a power failure occurs. After power recovery, the unit will automatically re-start in the same settings which were active before the power failure, except for timer settings. If the timers were set before a power failure, they will need to be re-set after power recovery. In the HEAT operation, the indoor fan may not start for two to five minutes after the unit is turned on to prevent cold air from blowing out of the unit. DE-ICING FUNCTION · When ice forms on the heat exchanger in the outdoor unit during the HEAT operation, an automatic de-icer provides heat for about 5 to 10 minutes to remove the ice. [. . . ]