User manual SHARP CD-BA2600

[. . . ] These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: q Reorient or relocate the receiving antenna. [. . . ] q Be sure to place 3" (8 cm) CD(s) in the middle of the disc trays. 1 2 7 3, 6 5 8 7 CD Caution: Do not stack CDs in the tray. This can damage the player and the CDs. 5 6 When loading a third disc, press the DISC SKIP button to turn the disc tray, then place the CD in the open position. Press the OPEN/CLOSE button to close the disc tray. 5 8 CD q The total number of tracks and the total playing time for one disc will be displayed. At this time, the disc number indicator is flashing. q The music schedule will be displayed only for the number of tracks on the disc. q If the CD contains more than 15 tracks, "C" will appear. 7 8 Press the desired disc number button ( Press the 0/R 1- 3). (0R) button. 2 1 q Playback will begin from track 1 on the disc you have selected to play. q After the disc finishes playing, the next disc will automatically play. q When there is no CD in one of the disc 1 - 3 positions, that position will be skipped and the next CD will be played. q When the last track on the third disc has finished playing, the unit will stop automatically. Music schedule More tracks indicator To interrupt playback: q "6" will appear. xPress the CD 6 button on the remote control. the 0R button to resume playback from the same To stop playback: Press the s (CD s) button. Total number of tracks Total playing time To remove the CDs: While in the stop mode, press the OPEN/CLOSE button. Notes: q When using random play, be sure to press the s (CD s) button after you are through listening. Otherwise, the disc(s) will play continuously. q In random play the unit will select and play tracks automatically. (You cannot select the order of the tracks. ) To cancel random play: Press the 0/R (0R) button. q "R" will go out. 9 (Continued) s APMS Selected disc number (Automatic Programmable Music Selector) You can playback the tracks on the CDs in the disc 1 - 3 positions in any order desired. By specifying the disc numbers from 1 to 3, and the track numbers from 1 to 99, you can choose up to 32 selections for playback in the order you like. 1 Selected track number Playback order When in the stop mode, use the disc number buttons ( 3) to select the desired disc number. Press the 5 1 2 3 2 1 3 5 4 or 4 button to select the desired track. Press the MEMORY/SET (MEMORY) button. q "MEMORY" will appear to show that the programmed sequence is being entered into memory. Up to 32 tracks can be programmed. q If you make a mistake while in the programming mode ("MEMORY" will appear) or if you wish to change your selections, the programmed tracks can be cleared by pressing the CLEAR button. The tracks will be cleared sequentially, starting with the last track entered. 5 1 3 CLEAR Press the 0/R (0R) button to start playback of programmed selections. To clear the programmed selections: 5 Press the CLEAR button on the remote control while the disc is stopped. q Each time the button is pressed, one track will be cleared, beginning with the last track programmed. Notes: q Opening the disc tray automatically cancels the programmed sequence. [. . . ] Read the demagnetizer's instructions carefully before use. q In order to ensure proper operation of the CD player, preventative maintenance (cleaning of the Laser Pick-up lens) should be performed periodically in order to keep the lens dust-free. Lens cleaners are commercially available. Contact your local CD software dealer for options. TAPE 2 s External care q Periodically wipe the cabinet with a soft cloth and a diluted soap solution, then wipe with a dry cloth. [. . . ]