User manual SHARP CD-C5H

[. . . ] To obtain the best performance from this product, please read this manual carefully. It will guide you in operating your SHARP product. Special Notes Important Instruction CAUTION - Introduction / Special Notes - Laser Diode Properties Material: GaAIAs Wavelength: 780 nm Emission Duration: continuous Laser Output: max. 0. 6 mW z This Mini Component System is classified as a CLASS 1 LASER product. z The CLASS 1 LASER PRODUCT label is located on the rear cover. [. . . ] (AM 0:00 - PM 11:59) To readjust the clock: Perform "Setting the Clock" from the beginning. If the time display is flashing, step 3 (for selecting the 24-hour or 12-hour display) will be skipped. To change the 24-hour or 12-hour display: 1 2 Clear all the programmed contents. [Perform to step 3 under "If trouble occurs" on page 31 for details. ] Perform "Setting the Clock" from the beginning. Note that this can only be set when the unit is first installed or it has been reset. (Refer to step 3 under "If trouble occurs" on page 31. ) E-13 ENGLISH Listening to a CD (CDs) This system can play audio CD-R and CD-RW discs just as CD discs, but cannot perform recording. (However, some CD-R and CD-RW discs may not be played. ) 1 2 3 4 Press the ON/STAND-BY button to turn the power on. Press the OPEN/CLOSE button to open the disc tray. Place the CD(s) on the disc tray, label side up. When loading a third disc, press the DISC SKIP button to turn the disc tray, then place the CD in the open position. z CDs can be placed on any open position on the disc tray. z Be sure to place 8 cm (3") CD(s) in the middle of the disc positions. 12 cm (5") 8 cm (3") 5 Press the OPEN/CLOSE button to close the disc tray. Total number of tracks on the CD whose number is flashing Total playing time of the CD whose number is flashing 6 To select the CD you want to listen to first, press one of the 3 buttons. 1- Continued to the next page Sound Control (See page 12. ) ENGLISH E-14 - Listening to a CD (CDs) - CD Playback Listening to a CD (CDs) (continued) 7 Press the ( ) button to start playback. , , To locate the beginning of a track To move to the beginning of the next track: Press the PRESET button for less than 0. 5 seconds during playback. z You can skip to any track by pressing the PRESET button repeatedly until the desired track number appears. button for less than 0. 5 seconds during playback. z You can skip to any track by pressing the PRESET button repeatedly until the desired track number appears. - Listening to a CD (CDs) - z Playback will begin from track 1 on the disc you have selected to play. On the other hand, the PRESET / button does not allow you to move to the previous track. The beginning of the track being played will be located. z In random play, the CD player will select and play tracks automatically. (You cannot select the order of the tracks. ) Notes: z When the DISC SKIP button is pressed during playback, the next disc will begin automatically. z When one of the 1 - 3 buttons is pressed during playback, the selected disc will begin automatically. Caution: After performing repeat or random play, be sure to press the disc(s) will play continuously. Otherwise, the ENGLISH E-16 CD Playback 2 - Starting Playback with a Desired Track / Repeat or Random Play - 1 To repeat all tracks on up to 3 discs: Whilst in the stop mode, press one of the 1 - 3 buttons or DISC SKIP button to select the desired disc. Programmed Play By specifying discs from 1 to 3, and tracks from 1 to 99, you can choose up to 32 selections for playback in the order you like. 3 Press the MEMORY/SET (MEMORY) button to save the track number. Playback order When the track is memorised, "MEMORY" will appear. 4 Repeat steps 1 - 3 for other tracks. Up to 32 tracks can be programmed. If you make a mistake, the programmed tracks can be cleared by pressing the CLEAR button. CD Playback 5 - Programmed Play - Press the ( ) button to start playback. To clear the programmed selections: Press the CLEAR button on the remote control whilst the "MEMORY" indicator is lit. Each time the button is pressed, one track will be cleared, beginning with the last track programmed. When all the tracks are cleared, "MEMORY" will disappear. Adding tracks to the programme: If a programme has been previously stored, the "MEMORY" indicator will be displayed. The new tracks will be stored after the last track of the original programme. 1 Whilst in the stop mode, press one of the 1 - 3 buttons to select the desired disc. Selected disc number Notes: z Opening the disc tray automatically cancels the programmed sequence. z Even if you press the ON/STAND-BY button to enter the stand-by mode or change the function from CD to another, the programmed selections will not be cleared. [. . . ] (Refer to step 3 under "If trouble occurs" on page 31. ) z No sound is heard. z Is the volume level set to "0"?z Is the karaoke mode set to "L-CH", "R-CH" or "V-CANCEL"? , , Karaoke Symptom z The vocal part of a multiplexed disc is not heard. Possible cause z Is the karaoke mode set to "L-CH", "R-CH" or "V-CANCEL"? , , CD player Symptom z Playback does not start. [. . . ]