User manual SHARP CD-C607H

[. . . ] Hnvisa till sidorna i till viii och V-1 till V-24. Leggere le pagine i a viii e I-1 a I-24. Raadpleeg de bladzijden i t/m viii en N-1 t/m N-24. Favor consultar as pginas i a viii e P-1 a P-24. [. . . ] TV AM loop aerial Installing the AM loop aerial < Assembling > To video input socket Video cable (not supplied) < Attaching to the wall > wall screws (not supplied) FM aerial Right speaker Left speaker Red Black Wall socket (AC 220 - 240 V ~ 50/60 Hz) Aerial connection Demonstration mode Supplied FM aerial: Connect the FM aerial wire to the FM 75 OHMS socket and position the FM aerial wire in the direction where the strongest signal can be received. External FM aerial: Use an external FM aerial (75 ohms coaxial cable) for better reception. When an external FM aerial is used, disconnect the supplied FM aerial wire. Supplied AM loop aerial: Connect the AM loop aerial to the AM and GND terminals. Position the AM loop aerial for optimum reception. Place the AM loop aerial on a shelf, etc. , or attach it to a stand or a wall with screws (not supplied). Note: Placing the aerial on the unit or near the AC power lead may cause noise pickup. Place the aerial away from the unit for better reception. The first time the unit is plugged in, the unit will enter the demonstration mode. To cancel the demonstration mode, press the DEMO button (remote control) during power stand-by mode. The unit will enter the low power consumption mode. To return to the demonstration mode, press the DEMO button again. Connecting iPod to a TV The iPod with photo and video can be viewed by connecting to a TV/monitor. Change the lighting or the direction of the unit if this occurs. Keep the remote control away from moisture, heat, shock, and vibrations. To turn the power on Press the ON/STAND-BY button to turn the power on. After use: Press the ON/STAND-BY button to enter the power stand-by mode. Display brightness control To dim the display brightness, hold down the CLEAR/ DIMMER button on the remote control for 2 seconds or more. Volume auto fade-in If you turn off and on the main unit with the volume set to 27 or higher, the volume starts at 16 and fades in to the last set level. Volume control Turn the volume knob towards VOL +/ (on main unit) or press VOLUME +/ (on remote control) to increase or decrease the volume. X-Bass control Test of the remote control Check the remote control after checking all the connections. Point the remote control directly at the remote sensor on the unit. The remote control can be used within the range shown below: Remote sensor MINI COMPONENT SYSTEM CD-DH790 When the power is first turned on, the unit will enter the extra bass mode which emphasises the bass frequencies, and "X-BASS" will appear. To cancel the extra bass mode, press the X-BASS button on the remote control. Bass control 1 Press the BASS/TREBLE button to select "BASS". 2 Within 5 seconds, press the VOLUME (+ or ) button to adjust the bass. Treble control 1 Press the BASS/TREBLE button to select "TREBLE". 2 Within 5 seconds, press the VOLUME (+ or ) button to FUNCTION ON/STAND-BY adjust the treble. 0. 2 m - 6 m (8" - 20') AUDIO IN PHONES VOL PUSH OPEN Equaliser When the EQUALIZER MODE button is pressed, the current mode setting will be displayed. To change to a different mode, press the EQUALIZER MODE button repeatedly until the desired sound mode appears. FLAT GAME No equalization. CLASSIC For classical music. POPS VOCAL E-6 JAZZ Setting the clock (Remote control only) Listening to the iPod Supported iPod models: iPod nano (software 1. 2 above) iPod mini (software 1. 2 above) iPod (5th generation) (software 1. 3 above) (Dock connector equipped Click Wheel model) iPod (4th generation) (software 3. 0. 2 above) (Dock connector equipped Click Wheel model) iPod nano (2nd generation) (software 1. 0. 0 above) iPod nano (3rd generation) (software 1. 0. 3 above) iPod nano (4th generation) (software 1. 0. 3 above) iPod classic (software 1. 0. 3 above) iPod touch (software 1. 1 above) iPod touch (2nd generation) (software 2. 1 above) Caution: Please update your iPod unit to the latest software version from Apple's homepage before using it. Notes: Once the iPod is connected to the unit it will begin charging. [. . . ] Make sure there is no CD in the disc tray. Then, set the unit to the power stand-by mode. Carrying the unit with iPod or USB memory device left docked or discs left inside can damage the unit. Care of compact discs Condensation Sudden temperature changes, storage or operation in an extremely humid environment may cause condensation inside the cabinet (CD pickup, etc. ) or on the transmitter on the remote control. Condensation can cause the unit to malfunction. [. . . ]