User manual SHARP CD-CH1000H

[. . . ] To obtain the best performance from this product, please read this manual carefully. It will guide you in operating your SHARP product. Contents Important Instruction !Important Instruction -Introduction/ContentsPage !Tape Playback Listening to a Cassette Tape . [. . . ] (Seconds are not displayed. ) The time display will disappear after a few seconds. Basic Operation Listening to a CD (CDs) This system can play audio CD-R and CD-RW discs just as CD discs, but cannot perform recording. 5 Press the DISC 1 button to close the disc tray 1. Means "disc inside" Total number of tracks Total playing time -Listening to a CD (CDs)- CD Playback 6 You can place discs on the trays 2 - 6 by following steps 3 - 5. Note: The system will search CD trays until it finds a CD and will not search the rest of trays. 7 !To play discs in turn (from Disc 1 to Disc 6) 1 Press the ON/STAND-BY button to turn the power on. 3 Press the DISC 1 button to open the disc tray 1. 4 Place a CD on the disc tray 1, label side up. " Be sure to place 8 cm (3") CD in the middle of the disc trays. 12 cm (5") 8 cm (3") Press the button to start playback. " Playback will begin from track 1 on the DISC 1. After that disc finishes playing, the next disc will automatically start playback. " When there is no CD in one of the disc tray 1 - 6 positions, that position will be skipped and the next CD will be played. " When the last track on the DISC 6 has finished playing, the CD player will stop automatically. E-17 ENGLISH Sound Control (See page 15. ) 01/1/25 E2. fm To interrupt playback: Press the button. To resume playback from the same point, press the To stop playback: Press the button. !To locate the beginning of a track button again. To move to the beginning of the next track: Turn the jog dial slowly clockwise by one position during playback. To exchange other CDs whilst playing a disc: Press the button for the stopped disc and exchange discs. Otherwise, the disc(s) will play continuously. " In random play, the CD player will select and play tracks automatically. (You cannot select the order of the tracks. ) To cancel repeat or random play: Press the PLAY MODE button repeatedly to select the normal play mode. The total remaining playing time for the disc will be displayed. Notes: " During random play, the total remaining playing time will not be displayed. " Depending on the CD, the playing time display may not match the total playing time which is indicated on the CD jacket, as the time between tracks is not included. E-19 ENGLISH 01/1/25 E2. fm Programmed Play By specifying discs from 1 to 6, and tracks from 1 to 99, you can choose up to 32 selections for playback in the order you like. 1 6 7 Press the Press the button. button to start playback. When in the stop mode, press the MEMORY button. " At this time, playback will not begin even if one of the DISC 1 - DISC 6 buttons is pressed. 2 Press one of the DISC 1 - DISC 6 buttons to select the desired disc. Selected disc number To cancel the programmed play mode: Whilst in the stop mode, press the CLEAR button. The MEMORY indicator will disappear and all the programmed content will be cleared. Advanced CD Playback To clear the programmed selections: Press the CLEAR button whilst the "MEMORY" indicator is flashing. Each time the button is pressed, one track will be cleared, beginning with the last track programmed. 3 Turn the jog dial to select the desired track. Adding tracks to the programme: If a programme has been previously stored, the "MEMORY" indicator will be displayed. The new tracks will be stored after the last track of the original programme. To check which tracks are programmed: Whilst the unit is stopped in the programmed play mode, press the or button. Selected track number Playback order 4 Press the MEMORY button to save the track number. Notes: " Opening any tray of the programmed discs automatically cancels the programmed sequence. " Even if you press the ON/STAND-BY button to enter the stand-by mode or change the function from CD to another function, the programmed selections will not be cleared. " During programme operation, random play is not possible. Playback time 5 Repeat steps 2 - 4 for other tracks. [. . . ] Cleaning the tape-handling parts " Dirty heads, capstans or pinch rollers can cause poor sound and tape jams. Clean these parts with a cotton swab moistened with commercial head/pinch roller cleaner or isopropyl alcohol. " When cleaning the heads, pinch rollers, etc. , unplug the unit which contains high voltages. C C D A B D !Clearing all the memory (reset) -Troubleshooting Chart/MaintenanceIf neither operation above restores the unit, clear all the memory by following the instructions below. [. . . ]