User manual SHARP CD/CP-C5300/H

[. . . ] Customers without Internet access may telephone 08705 274277 during office hours (or (01) 676 0648 if telephoning from Ireland). 0101 SHARP CORPORATION 03/11/28 CDDP900S(E)_FR. pm6 TINSEA032AWZZ CD/CP-C5300/H Special notes NOTES FOR USERS IN THE U. K. AND IRELAND The mains lead of this product is fitted with a non-rewireable (moulded) plug incorporating a 3A fuse. Should the fuse need to be replaced, a BSI or ASTA approved BS 1362 fuse marked or and of the same rating as above, which is also indicated on the pin face of the plug must be used. Always refit the fuse cover after replacing the fuse. [. . . ] To resume playback from the same point, press the button. To stop playback: Press the (CD ) button. To remove the CDs: 12 cm (5") 8 cm (3") Whilst in the stop mode, press the OPEN/CLOSE button. Then, press the DISC SKIP button to rotate the disc tray and remove the remaining disc. After use: Press the ON/STAND-BY button to enter the power stand-by mode. 16 Sound control (See page 14. ) 03/11/28 CD/CP-C5300/H(E)2. fm TINSEA032AWZZ CD/CP-C5300/H " To locate the beginning of a track To move to the beginning of the next track: Press the / button for less than 0. 5 seconds during playback. You can skip to any track by pressing the sired track number appears. " Starting playback with a desired track You can play a disc starting with the desired track. 1 2 Whilst in the stop mode, press the DISC SKIP button to select the desired disc. Press the / or / button to select the desired track. Selected disc number To restart the track being played: Press the / button for less than 0. 5 seconds during playback. You can skip to any track by pressing the sired track number appears. 4 Notes: " To locate the desired portion For audible fast forward: Press and hold down the Press and hold down the / / button during playback. button during playback. Selected track number You can also select a track by pressing the remote control. / or / button on the 3 Press the / ( ) button to start playback. Playback of the selected track is started. When the end of last track of the disc selected is reached, the next disc will be automatically started. For audible fast reverse: Notes: / or / button is released. You can locate the desired portion on a single disc only. When the end of the last track is reached during fast forward, "END" will appear on the display and CD operation will be paused. When the beginning of the first track is reached during fast reverse, the unit will enter the playback mode. / or / button on the remote control allows you to locate the !In random play, the CD player will select and play tracks automatically. (You cannot select the order of the tracks. ) Adding tracks to the programme: If a programme has been previously stored, the "MEMORY" indicator will be displayed. The new tracks will be stored after the last track of the original programme. Notes: !Opening the disc tray automatically cancels the programmed sequence. Even if you press the ON/STAND-BY button to enter the stand-by mode or change the function from CD to another, the programmed selections will not be cleared. During programme operation, random play is not possible. Caution: After performing repeat or random play, be sure to press the wise, the disc(s) will play continuously. Other- 18 03/11/28 CD/CP-C5300/H(E)2. fm TINSEA032AWZZ Listening to the radio " Tuning CD/CP-C5300/H 1 2 3 Press the ON/STAND-BY button to turn the power on. Press the TUNER (BAND) button repeatedly to select the desired frequency band (FM or AM). Manual tuning: Press the TUNING/TIME button as many times as required to tune in to the desired station. or ) button to tune in to the desired 5 - Listening to the radio - Auto tuning: When the TUNING/TIME button is pressed for more than 0. 5 seconds, scanning will start automatically and the tuner will stop at the first receivable broadcast station. Notes: !When radio interference occurs, auto scan tuning may stop automatically at that point. Auto scan tuning will skip weak signal stations. [. . . ] Clean these parts with a cotton swab moistened with commercial head/pinch roller cleaner or isopropyl alcohol. " When cleaning the heads, pinch rollers, etc. , unplug the unit which contains high voltages. TAPE 1 A B C Specifications As part of our policy of continuous improvement, SHARP reserves the right to make design and specification changes for product improvement without prior notice. The performance specification figures indicated are nominal values of production units. There may be some deviations from these values in individual units. ! [. . . ]