User manual SHARP CD/CP-C770/H

[. . . ] Customers without Internet access may telephone 08705 274277 during office hours (or (01) 676 0648 if telephoning from Ireland). 0101 CD/CP-C770/H Special notes WARNINGS NOTES FOR USERS IN THE U. K. AND IRELAND The mains lead of this product is fitted with a non-rewireable (moulded) plug incorporating a 3A fuse. Should the fuse need to be replaced, a BSI or ASTA approved BS 1362 fuse marked or and of the same rating as above, which is also indicated on the pin face of the plug must be used. Always refit the fuse cover after replacing the fuse. [. . . ] Readjust the clock as follows. "0:00" "AM 12:00" "AM 0:00" The 24-hour display will appear. (0:00 - 23:59) The 12-hour display will appear. (AM 12:00 - PM 11:59) The 12-hour display will appear. To readjust the clock: Perform "Setting the clock" from the beginning. If the time display is flashing, step 3 (for selecting the 24-hour or 12-hour display) will be skipped. To change the 24-hour or 12-hour display: 1 2 Clear all the programmed contents. [Refer to "Clearing all the memory (reset)" on page 30 for details. ] Perform "Setting the clock" from the beginning. (AM 0:00 - PM 11:59) Note that this can only be set when the unit is first installed or it has been reset. [Refer to "Clearing all the memory (reset)" on page 30 for details. ] 14 01/7/17 CD/CP-C770/H_2. fm Listening to a CD (CDs) 1 2 3 4 Press the ON/STAND-BY button to turn the power on. Press the OPEN/CLOSE button to open the disc tray. CD/CP-C770/H Place the CD(s) on the disc tray, label side up. When loading a third disc, press the DISC SKIP button to turn the disc tray, then place the CD in the open position. " CDs can be placed on any open position on the disc tray. " Be sure to place an 8 cm (3") CD(s) in the middle of the disc positions. 5 Press the OPEN/CLOSE button to close the disc tray. Music schedule Total number of tracks on the CD whose number is flashing Total playing time of the CD whose number is flashing The music schedule will display only the number of tracks on the disc. If the CD contains more than 15 tracks, " " will appear. 6 To select the CD you want to listen to first, press one of the DISC1 - DISC-3 buttons. Continued to the next page 01/7/17 CD/CP-C770/H_2. fm CD Playback 12 cm (5") 8 cm (3") 15 - Listening to a CD (CDs) - CD/CP-C770/H Listening to a CD (CDs) (continued) 7 Press the / ( ) button to start playback. !To locate the beginning of a track To move to the beginning of the next track: Press the button for less than 0. 5 seconds during playback. / or / button on the 3 Press the / ( ) button to start playback. To cancel random play: Press the button. Playback of the selected track starts. When the end of the last track is reached on the selected disc, the next disc will automatically start playback. To stop playback: Press the (CD ) button. Notes: " If you press the / button during random play, you can move to the track selected next by the random operation. On the other hand, the / button does not allow you to move to the previous track. The beginning of the track being played will be located. " In random play, the CD player will select and play tracks automatically. (You cannot select the order of the tracks. ) Notes: " When the DISC SKIP button is pressed during playback, the next disc will begin automatically. " When one of the DISC-1 - DISC-3 buttons is pressed during playback, the selected disc will begin automatically. Caution: After performing repeat or random play, be sure to press the wise, the disc(s) will play continuously. Other- 01/7/17 CD/CP-C770/H_2. fm CD Playback 2 Press the or button to select the desired track. To cancel repeat play: Press the / ( " " will go out. ) button again. 17 - Listening to a CD (CDs) / Repeat or random play - CD/CP-C770/H Programmed play You can choose up to 32 selections for playback in the order you like. 2 Press the or button to select the desired track. You can also select a track by pressing the remote control. / Selected track number or / button on the 3 Press the MEMORY/SET (MEMORY) button to save the track number. CD Playback - Programmed play - Playback order When the track is memorised, "MEMORY" will appear. 4 Repeat steps 1 - 3 for other tracks. Up to 32 tracks can be programmed. If you make a mistake, the programmed tracks can be cleared by pressing the CLEAR button. 5 Press the / ( ) button to start playback. To clear the programmed selections: Press the CLEAR button on the remote control whilst the "MEMORY" indicator is lit. [. . . ] Clean these parts with a cotton swab moistened with a commercial head/pinch roller cleaner or isopropyl alcohol. When cleaning the heads, pinch rollers, etc. , unplug the unit which contains high voltages. A B C TAPE 1 Note: - Troubleshooting chart / Maintenance - If neither operation above restores the unit, clear all the memory by resetting it. D E B C TAPE 2 " Clearing all the memory (reset) 1 2 Press the ON/STAND-BY button to enter the power stand-by mode. Whilst pressing down the / button and the X-BASS/DEMO button, press the ON/STAND-BY button until "CLEAR AL" appears. Playback head Capstan Pinch roller Erase head Recording/Playback head References ! [. . . ]