User manual SHARP CD/CP-S600H

[. . . ] Mini sistemi CD/CP-S600H composto da CD/CP-S600H (apparecchio principale) e CP-XP120H (sistema di diffusori). CD/CP-S600H mini systeem bestaande uit CD/CP-S600H (hoofdtoestel) en CPXP120H (luidsprekersysteem). CD/CP-S600H Mini Sistema de Componentes composto de CD/CP-S600H (unidade principal) e CP-XP120H (sistema de alto-falante). CD/CP-S600H Mini Component System consisting of CD/CP-S600H (main unit) and CP-XP120H (speaker system). CD/CP-S600H BEDIENUNGSANLEITUNG MODE D'EMPLOI MANUAL DE MANEJO BRUKSANVISNING MANUALE DI ISTRUZIONI GEBRUIKSAANWIJZING MANUAL DE OPERAO OPERATION MANUAL DEUTSCH FRANAIS ESPAOL SVENSKA ITALIANO NEDERLANDS PORTUGUS ENGLISH Siehe Seiten i bis vi und D-1 bis D-26. [. . . ] " Never use a power lead other than the one supplied. Otherwise, a malfunction or an accident may occur. !To turn the power on Press the ON/STAND-BY button to turn the power on. After use: Press the ON/STAND-BY button to enter the power stand-by mode. - System connections - To return to the demonstration mode: When the unit is in the power stand-by mode, press the EQUALIZER/X-BASS/DEMO button again. 8 E-8 02/4/15 CD/CP-S600H(H)E1. fm CD/CP-S600H Remote control !Battery installation 1 2 Remove the battery cover. Insert the batteries according to the direction indicated in the battery compartment. When inserting or removing the batteries, push them towards the battery terminals. Notes concerning use: " Replace the batteries if the operating distance is reduced or if the operation becomes erratic. Purchase 2 "AA" size batteries (UM/ SUM-3, R6, HP-7 or similar). " Periodically clean the transmitter on the remote control and the sensor on the unit with a soft cloth. " Exposing the sensor on the unit to strong light may interfere with operation. The hour will not advance even if minutes advance from "59" to "00". 3 Within 30 seconds, press the PRESET ( or ) button to select 24-hour or 12-hour display and then press the MEMORY/SET button. To confirm the time display: Press the CLOCK button. The time display will appear for about 8 seconds. Note: The time will flash at the push of the CLOCK button when the AC power supply is restored after a power failure or unplugging the unit. Readjust the clock as follows. "0:00" The 24-hour display will appear. (0:00 - 23:59) "AM 12:00" The 12-hour display will appear. (AM 12:00 - PM 11:59) Note that this can only be set when the unit is first installed or it has been reset. [Refer to "Clearing all the memory (reset)" on page 24 for details. ] To readjust the clock: Perform "Setting the clock" from the beginning. If the time display is flashing, step 3 (for selecting the 24-hour or 12-hour display) will be skipped. To change the 24-hour or 12-hour display: 1 Clear all the programmed contents. [Refer to "Clearing all the memory (reset)" on page 24 for details. ] 2 Perform "Setting the clock" from the beginning. E-11 02/4/15 CD/CP-S600H(H)E2. fm Listening to a CD (CDs) This system can also play audio CD-R and CD-RW discs, but cannot record. Some audio CD-R and CD-RW discs may not be playable due to the state of disc or the device that was used for recording. CD/CP-S600H ENGLISH 4 Place the CD(s) on the disc tray, label side up. When loading a third disc, press the DISC SKIP button to turn the disc tray, then place the CD in the open position. [. . . ] 2 Remove all discs from the unit and close the disc tray. 3 Press the ON/STAND-BY button to enter the stand-by mode. 4 When "SHARP" disappears, unplug the AC power lead from the wall socket. 5 Insert the transport screw into the back of the unit and tighten it with a flat-blade screwdriver or a coin. [. . . ]