User manual SHARP CD-G14000

[. . . ] MINI COMPONENT SYSTEM SISTEMA MINI COMPONENTE MODEL MODELO The illustrations printed in this operation manual are for the model CD-G14000 Las ilustraciones impresas en este manual de operaciones son para el modelo CD-G14000 CD-G14000 CD-G14000/CD-G17000/ CD-G22000 CD-G17000 SPEAKER SYSTEM SISTEMA DE BOCINAS MODEL MODELO CD-G22000 CD-G17000 CD-G22000 CP-G14000S/CP-G17000S/ CP-G22000S OPERATION MANUAL MANUAL DE MANEJO ENGLISH ENGLISH ESPAÑOL ESPAÑOL Please refer to pages ENGLISH E-1 to E-47. Please refer to pagesi ito iii and E-1 to E-47. to iii and Please Consulte las páginasESPAÑOL aa S-47. Consul iii y S-1 Consulte las páginasi iaa iii y S-1 S-47. CD-G14000 CD-G17000 CD-G22000 SPECIAL NOTES NOTE This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. [. . . ] To stop playback: Press the (CD ) button. E-24 CD-G14000 CD-G17000 CD-G22000 ENGLISH Repeat play Repeat play can play all 5 discs, all tracks on a chosen disc, or a programmed sequence continuously. To repeat one disc: Press the / button twice. To repeat all tracks on up to 5 discs: Press the / button three times. To repeat desired tracks: Perform steps 1 - 6 in "Programmed play" section on page 26 and then press the / button twice. Random play The tracks on the disc(s) can be played in random order automatically. To random play all tracks on up to 5 discs: Press the RANDOM button on the remote control. To cancel random play: Press the / button. Notes: If you press the button during random play, you can move to the next track by the random operation. On the other hand, the button does not allow you to move to the previous track. The beginning of the track being played will be located. In random play, the unit will select and play tracks automatically. (You cannot select the order of the tracks. ) Caution: After performing repeat or random play, be sure to press the (CD ) button. Otherwise, the disc(s) will play continuously. To cancel repeat play: Press the / button again. " " will disappear. E-25 CD or MP3/WMA disc Playback CD-G14000 CD-G17000 CD-G22000 Advanced CD or MP3/WMA disc playback (continued) Programmed play You can choose up to 32 selections for playback in the order you like. To clear the programmed selections: Press the CLEAR/DIMMER button on the remote control whilst the "MEMORY" indicator is flashing. Each time the button is pressed, one track will be cleared, beginning with the last track programmed. To cancel the programmed play mode: Whilst in the stop mode and the "MEMORY" indicator is lit, press the CLEAR/DIMMER button on the remote control. The "MEMORY" indicator will disappear and all the programmed contents will be cleared. Adding tracks to the programme: If a programme has been previously stored, the "MEMORY" indicator will be displayed. The new tracks will be stored after the last track of the original programme. To check which tracks are programmed: Whilst the unit is stopped in the programmed play mode, press the or button. Notes: When a disc with programmed tracks is ejected, the programme is automatically cancelled. Even if you press the ON/STAND-BY button to enter the stand-by mode or change the function from CD to another, the programmed selections will not be cleared. During the programme operation, random play is not possible. ENGLISH 1 Whilst in the stop mode, press the MEMORY button to enter the programming save mode. CD or MP3/WMA disc Playback 2 Press one of the 1 - 5 buttons to select the desired disc. Selected disc number 3 Press the direct search buttons on the remote control to select the desired track. [. . . ] Does the remote control sensor receive strong light? E-43 References CD-G14000 CD-G17000 CD-G22000 Troubleshooting chart (continued) If problem occurs When this product is subjected to strong external interference (mechanical shock, excessive static electricity, abnormal supply voltage due to lightning, etc. ) or if it is operated incorrectly, it may malfunction. If such a problem occurs, do the following: 1 Set the unit to the stand-by mode and turn the power on again. 2 If the unit is not restored in the previous operation, unplug and plug in the unit, and then turn the power on. Note: If neither operation above restores the unit, clear all the memory by resetting it. ENGLISH Before transporting the unit Remove all CDs from the unit. [. . . ]