User manual SHARP CD-G7500DVD

[. . . ] or theft, please record below the model number and serial However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to number which are located on the rear of the unit. radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interPlease retain this information. ference by one or more of the following measures: Model number ______________________________ q Reorient or relocate the receiving antenna. [. . . ] q The volume is adjusted in 1 dB steps up or down each time you press the CENTER LEVEL button or the SURROUND LEVEL button. q The volume settings for the center and rear speakers are stored in memory for future use. However, if the power is disconnected or there is a power failure, the levels will return to their initial settings. 2 3 Play the video software program. To cancel the Dolby Pro Logic Surround mode, press the BYPASS button on the main unit or the DOLBY PRO LOGIC button on the remote control until "BYPASS" appears. q The BYPASS button will light. Note: q You cannot use the Dolby Pro Logic Surround feature with headphones. 11 SETTING THE CLOCK (Main unit operation) In this example, the clock is set for the 12-hour (AM 12:00) system. MEMORY/SET POWER ON/ STAND-BY CLOCK 1 2 3 4 Press the ON/STAND-BY button to enter the stand-by mode. Within 5 seconds, press the MEMORY/SET button. TUNING/ TIME ( ) Press the TUNING/TIME (X or button to select the time display mode. "AM 12:00" The 12-hour display will appear. (AM 12:00 - PM 11:59) "AM 0:00" The 12-hour display will appear. (AM 0:00 - PM 11:59) "0:00" The 24-hour display will appear. (0:00 - 23:59) q Note that this can only be set when the unit is first installed or it has been reset (see page 21). W) 2 3 4 AM 12:00 AM 0:00 0:00 5 6 Press the MEMORY/SET button. Press the TUNING/TIME (X or W) button to adjust the hour. the 0R button to resume playback from the same To stop playback: Press the s (CD s) button. Total number of tracks Total playing time To remove the CDs: While in the stop mode, press the OPEN/CLOSE button. Then, press the DISC SKIP button to rotate the disc tray and remove the remaining disc. After use: Press the ON/STAND-BY button to enter the stand-by mode. 13 (Continued) s Disc number selection 1 2 When stopped, press the DISC SKIP button. Press the 0/R (0R) button. q The next disc playback will begin, after which each following disc will be played sequentially. Notes: q When the DISC SKIP button is pressed during playback, playback will begin automatically from the next disc. (It is not necessary to press the 0/R (0R) button. ) q When one of the disc number buttons ( 1- 3) is pressed during playback, playback of the selected disc will begin automatically. (It is not necessary to press the 0/R (0R) button. ) DISC SKIP s APSS (Auto Program Search System) APSS automatically locates the beginning of any track. To listen again to the track being played: Press the 5 button for less than 0. 5 seconds during playback. To move to the beginning of the next track: Press the 4 button for less than 0. 5 seconds during playback. q To skip a number of tracks at one time, press the 5 or 4 button repeatedly until the desired track number is shown. q To start playing at a desired track, press the 5 or 4 button while in the stop mode to select the track number, and then press the 0/R (0R) button. [. . . ] Press the ON/STAND-BY button to enter the stand-by mode, and then unplug the AC power cord from the AC outlet. CD q Remove all CDs inserted in the unit. q Make sure that "NO DISC" is displayed. SPECIFICATIONS As part of our policy of continuous improvement, SHARP reserves the right to make design and specification changes for product improvement without prior notice. The performance specification figures indicated are nominal values of production units. There may be some deviations from these values in individual units. q General Power source: Power consumption: Dimensions: Weight: AC 120 V, 60 Hz 150 W Width; 10-5/8" (270 mm) Height; 13" (330 mm) Depth; 14" (355 mm) 18. 2 lbs. [. . . ]