User manual SHARP CD-MPS600W

[. . . ] These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. [. . . ] " " will go out. To random play all tracks on the chosen disc: 1 Press one of the 1 - 5 buttons. 2 Within 5 seconds, press the DIRECT PLAY button. 3 Press the RANDOM button on the remote control. To cancel random play: Press the DIRECT PLAY button. Notes: If you press the button during random play, you can move to the track selected next by the random operation. On the other hand, the button does not allow you to move to the previous track. The beginning of the track being played will be located. In random play, the CD player will select and play tracks automatically. (You cannot select the order of the tracks. ) Caution: After performing repeat or random play, be sure to press the ton. Otherwise, the disc(s) will play continuously. but- 19 04/1/19 CD-MPS600W(U)2. fm TINSEA055AWZZ CD Playback To cancel random play: Press the / button. If the FM reception is weak, press the TUNER (BAND) button to extinguish the "ST" indicator. The reception changes to monaural, and the sound becomes clearer. FM stereo mode indicator or ) button to tune in to the desired CD-MPS600W 5 Auto power on function: When you press any of the following buttons, the unit turns on. TUNER (BAND) button (main unit and remote control): The unit turns on and the "TUNER" function is activated. / button (main unit and remote control): The unit turns on and playback of the last function starts (CD/TAPE/TUNER/ GAME). FM stereo receiving indicator 21 04/1/19 CD-MPS600W(U)3. fm TINSEA055AWZZ Radio CD-MPS600W Listening to the radio (continued) Memorizing a station You can store 40 AM and FM stations in memory and recall them at the push of a button. (Preset tuning) 1 2 To recall a memorized station ) button for less than 0. 5 seconds to se- Press the PRESET ( or lect the desired station. 1 2 Perform steps 1 - 3 in "Tuning" on page 21. Press the MEMORY/SET (MEMORY) button to enter the preset tuning saving mode. To scan the preset stations The stations saved in memory can be scanned automatically. (Preset memory scan) Press the PRESET ( or ) button for more than 0. 5 seconds. The preset number will flash and the programmed stations will be tuned in sequentially, for 5 seconds each. Press the PRESET ( or ) button again when the desired station is located. 3 Within 30 seconds, press the PRESET ( select the preset channel number. or ) button to Radio Store the stations in memory, in order, starting with preset channel 1. 4 Within 30 seconds, press the MEMORY/SET (MEMORY) button to store that station in memory. If the "MEMORY" and preset number indicators go out before the station is memorized, repeat the operation from step 2. 5 Repeat steps 1 - 4 to set other stations, or to change a preset station. When a new station is stored in memory, the station previously memorized will be erased. 1 2 To erase entire preset memory Press the ON/STAND-BY button to enter the stand-by mode. [. . . ] Contact your local CD software dealer for options. NO YES Correct Cleaning the cabinet Periodically wipe the cabinet with a soft cloth and a diluted soap solution, then with a dry cloth. Caution: Do not use chemicals for cleaning (gasoline, paint thinner, etc. ). Do not apply oil to the inside of the unit. It may cause malfunctions. 34 04/1/19 CD-MPS600W(U)3. fm TINSEA055AWZZ Specifications As part of our policy of continuous improvement, SHARP reserves the right to make design and specification changes for product improvement without prior notice. [. . . ]