User manual SHARP CDBA2000 OPERATION MANUAL

[. . . ] In the unlikely event of the socket outlet in your home not being compatible with the plug supplied, cut-off the mains plug and fit an appropriate type. DANGER: The fuse from the cut-off plug should be removed and the cut-off plug destroyed immediately and disposed of in a safe manner. Under no circumstances should the cut-off plug be inserted elsewhere into a 13A socket outlet as a serious electric shock may occur. To fit an appropriate plug to the mains lead, follow the instructions below: IMPORTANT: The wires in the mains lead are coloured in accordance with the following code: Blue : Neutral Brown : Live As the colours of the wires in the mains lead of this product may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows: q The wire which is coloured blue must be connected to the plug terminal which is marked N or coloured black. [. . . ] z When a new station is stored in the selected station preset number memory, the contents previously memorised will be erased. z To store an RDS station in memory, perform steps 2 - 4 whilst the RDS station name is displayed. (Main unit operation) To erase all the contents in the preset memory: 1 Press the ON/STAND-BY button to enter the stand-by mode. 2 Press the ON/STAND-BY button whilst holding down the TUNER (BAND) button and the EQUALIZER/X-BASS/ DEMO button. z After performing this operation, all of the preset memory information will be erased. 1 2 3 Perform steps 1 - 6 in the "Tuning" section. , , Preset memory scan The stations saved in the preset memory can be scanned automatically. To scan the preset stations, press the PRESET ( or ) button for more than 0. 5 seconds. z The station preset number will flash and the programmed stations will be tuned in sequentially, for 5 seconds each. 4 1 2 Press the PRESET ( or ) button again to stop the memory scan at the desired station. 5 PRESET( ) 3 PRESET ( ) 2, 4 Note: When the preset memory does not have any stations stored in it, the preset memory scan will not function. To recall a memorised station: Press the PRESET ( or ) button for less than 0. 5 seconds to select the desired station. z The stations (preset channel number, frequency and frequency band) which have been stored in memory will appear in the display in numerical order, irrespective of the frequency bands. Note: When searching for a memorised station, do not press the PRESET button for more than 0. 5 seconds. When the PRESET button is pressed for more than 0. 5 seconds, the unit will enter the preset memory scan mode. Backup function: The backup function protects all station presets for a few hours should there be a power failure or the AC power lead is removed from the AC socket. 15 RDS (Radio Data System) OPERATION RDS is a broadcasting service which a growing number of FM stations are now providing. Music in this category is often but not always, vocal, and usually of short duration. Classical music for general, rather than specialist appreciation. Examples of music in this category are instrumental music, and vocal or choral works. AFFAIRS: INFO: SPORT: EDUCATE: DRAMA: CULTURE: , , Information Provided by RDS With the CD-BA1300H, you can display three types of RDS service. To show them in the display, press the DISPLAY MODE button. Each time you press the DISPLAY MODE button, the display will change to show the following information. SCIENCE: VARIED: PS PTY RT Station Frequency POP M: PS (Programme Ser- Station names commonly known will be displayed. "NO PS" appears vice) if no signal is received. PTY (Programme Type) RT (Radio Text) Programme type will be displayed. "NO PTY" appears if no signal is received. "NO RT" appears if no signal is received. LIGHT M: ROCK M: EASY M: Station Frequency DISPLAY MODE 16 (Continued) CLASSICS: Performances of major orchestral works, symphonies, chamber music, etc. , and including Grand Opera. [. . . ] (Maximum: 3 hours - Minimum: 1 minute) The amount of sleep time can also be changed during the sleep operation. z 3 hours - 5 minutes 5-minute intervals z 5 minutes - 1 minute 1-minute intervals 3 Press the MEMORY/SET button. 4 The unit will enter the stand-by mode automatically after the preset sleep time has elapsed. Note: z Once the sleep time is set, it will remain the same duration until the setting is changed. To confirm the remaining sleep time: Press the TIMER/SLEEP button. To cancel the sleep operation: Press the ON/STAND-BY button to enter the stand-by mode. 30 RESETTING THE MICROCOMPUTER Reset the microcomputer under the following conditions: z To erase all of the stored memory contents (clock and timer settings, and tuner and CD presets). z If the operation is not correct. MAINTENANCE , , Internal care z Dirty heads, capstans or pinch rollers can cause poor sound and tape jams. [. . . ]