User manual SHARP CDBA3000 OPERATION MANUAL PART (FROM THE SERVICE MANUAL)
Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual SHARP CDBA3000. We hope that this SHARP CDBA3000 user guide will be useful to you.
Lastmanuals help download the user guide SHARP CDBA3000.
Manual abstract: user guide SHARP CDBA3000OPERATION MANUAL PART (FROM THE SERVICE MANUAL)
Detailed instructions for use are in the User's Guide.
[. . . ] SETTING THE CLOCK
Reset the microcomputer under the following conditions:
q To erase all of the stored memory contents (clock and timer settings, and tuner and CD presets). q If the operation is not correct.
RESETTING THE MICROCOMPUTER
CD-BA3000H
(Main unit operation)
In this example, the clock is set for the 24-hour (0:00) system.
1 Press the ON/STAND-BY button to enter the stand-by mode. [. . . ] (0:00 - 23:59) "AM 0:00" The 12-hour display will appear. (AM 0:00 - PM 11:59) "AM 12:00" The 12-hour display will appear. (AM 12:00 - PM 11:59) q Note that this can only be set when the unit is first installed or it has been reset.
5 Press the MEMORY/SET button. 6 Press the TUNING/TIME ( or ) button to adjust the hour.
PREPARATION FOR USE
q Press the TUNING/TIME ( or ) button once to advance the time by 1 hour. q When the 12-hour display is selected, "AM" will change automatically to "PM".
s Remote control
7 Press the MEMORY/SET button. 8 Press the TUNING/TIME ( or ) button to adjust the min0. 2 m - 6 m (8" - 20')
utes. q Press the TUNING/TIME ( or ) button once to advance the time by 1 minute. Hold it down to change the time in 5 minute intervals. q The hour setting will not advance even if minutes advance from "59" to "00".
Notes concerning use: q Replace the batteries if the operating distance is reduced or if the operation becomes erratic. q Periodically clean the transmitter LED on the remote control and the sensor on the main unit with a soft cloth. [. . . ] q The time display will appear for about 5 seconds.
Note: q The clock display will flash on and off at the push of the CLOCK button when the AC power supply is restored after a power failure occurs or after the AC power lead is disconnected. If this happens, follow the procedure below to change the clock time.
To change the clock time:
1 Press the CLOCK button.
2 Within 5 seconds, press the MEMORY/SET button.
3 Perform steps 6 - 9 above.
To change the time display mode:
1 Perform steps 1 - 2 in the section "RESETTING THE MICROCOMPUTER".
2 Perform steps 1 - 9 above. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE SHARP CDBA3000
Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.
Click on "Download the user manual" at the end of this Contract if you accept its terms, the downloading of the manual SHARP CDBA3000 will begin.
