User manual SHARP CDC421H OPERATION MANUAL

[. . . ] . 46 CD-C491H(SUK) TINSE0229AWZZ YO <P=001> SPECIAL NOTES NOTE FOR USERS IN THE U. K. The mains lead of this product is fitted with a non-rewireable (moulded) plug incorporating a 3A fuse. Should the fuse need to be replaced, a BSI or ASTA approved BS 1362 fuse marked or and of the same rating as above, which is also indicated on the pin face of the plug must be used. Always refit the fuse cover after replacing the fuse. Never use the plug without the fuse cover fitted. [. . . ] q If a 40th station is stored in memory during a scan, the scanning will stop at that station. The number of stations and "END" will each be displayed for 4 seconds. q If no stations have been stored in memory, "END" will flash for about 4 seconds. q If 40 stations have already been stored in memory and the ASPM button is pressed, "END" will appear immediately and the scan will be aborted. If you want to redo the ASPM operation from the beginning, erase the preset memory, and then perform steps 1 - 4. (4 seconds) To stop the ASPM operation before it is complete: Press the ASPM button whilst it is scanning for stations. q The stations that have already been stored in memory will be kept there. (4 seconds) To erase all of the contents of preset memory: The unit is in the stand-by mode. Hold down the TUNER button and the s button, and then press the ON/STAND-BY button. q After performing this operation, all of the preset memory information will be erased. 20 CD-C491H(SUK) TINSE0229AWZZ (Continued) s To recall stations that have been stored in memory (PTY search) PTY. TI SEARCH TUNER (BAND) You can select a group of stations by specifying the programme type (news, sports, traffic programme, etc. see page 19) from among the stations that have been stored in memory. (ASPM is convenient for storing stations in memory. ) ON/ STAND-BY Jog dial 1 2 3 4 PTY. TI PRESET Press the ON/STAND-BY button to turn the power on. Press the TUNER (BAND) button to select the FM ST or FM band. ("Programme type" "WAITING") To cancel the EON stand-by mode: When in the EON stand-by mode, press the EON button. The EON stand-by mode will be cancelled. Notes: In the following cases, the EON stand-by mode will be cancelled. q When the unit is set in the stand-by mode q When the unit is switched to another band in the EON stand-by 5 mode q When you change the FM station whilst in the EON stand-by mode q When a preset call is made About the TP and TA indicators TP indicator Not lit Not lit Lit TA indicator Not lit Lit Not lit Meaning This programme does not carry traffic announcements nor does it refer, via EON, to a programme that does. This programme carries EON information about another programme which gives traffic information. This programme carries traffic announcements but none are being broadcast at present and may also carry EON information about other traffic announcements. A traffic announcement is being broadcast on this programme at present. Lit Lit 23 CD-C491H(SUK) TINSE0229AWZZ (Continued) s EON-TI PTY. TI SEARCH EON 1 2 3 4 Tune in the desired RDS station, then the PS name will be displayed. Press the EON button when "EON" appears. q "PTY. TI" and "SELECT" will appear alternately for about 4 seconds. Whilst they are being displayed, select the TI (Traffic Information) turning the jog dial. Within 4 seconds, press the PTY. TI SEARCH button. q The selected "TI" will flash. Jog dial q "TI" and "WAITING" will appear for 2 seconds each. q "TI" will appear, and the unit will enter the EON-TI stand-by mode. 5 When a TA specifed starts on a other network station, the unit will automatically switch to that station, and "TI" will flash. [. . . ] (No video signal is output except when DVD 1, VCR 1, DVD 2 or VCR 2 is selected. ) q Insert the batteries properly. q Operate it within a range of 0. 2 m (8") to 6 m (20') and within an angle of 15° to either side of centre. q Connect the AC power lead. q No sound is heard from the sub q Were the headphones plugged in woofer. and then unplugged? q No picture is seen on the TV. q Is the correct function selected? q The remote control does not function or does not operate properly. q The batteries (polarity) are not inserted properly. [. . . ]