User manual SHARP CDC491H OPERATION MANUAL

[. . . ] MINI COMPONENT SYSTEM OPERATION MANUAL MODEL CD-C491H Thank you for purchasing this SHARP product. To obtain the best performance from this product, please read this manual carefully. It will guide you in operating your SHARP product. CD-C491H mini component system consisting of CD-C491H mini component system, CP-C491, CP-SW491, centre (GBOXS0010AWM2) and surround (GBOXS0011AWM2) speaker system. CONTENTS Page SPECIAL NOTES . 17-18 RDS (Radio Data System) OPERATION . [. . . ] see page 19) from among the stations that have been stored in memory. (ASPM is convenient for storing stations in memory. ) ON/ STAND-BY Jog dial 1 2 3 4 PTY. TI PRESET Press the ON/STAND-BY button to turn the power on. Press the TUNER (BAND) button to select the FM ST or FM band. Press the PTY. TI SEARCH button. q "PTY. TI" and "SELECT" will appear alternately for about 4 seconds. 5 Within 4 seconds, turn the jog dial on the main unit or press the or button on the remote control to select the programme type you want. XW Programme type: TUNER (BAND) ON/STAND-BY NEWS DRAMA ROCK M ALARM AFFAIRS CULTURE M. O. R. M TP* INFO SPORT EDUCATE SCIENCE VARIED POP M LIGHT M CLASSICS OTHER M TA q Each time the button on the remote control is pressed the programme type will appear in order as shown above. If the button is held down for more than 0. 5 seconds the programme type will continuously change. 6 4 Whilst the selected programme type is flashing (within 4 seconds), press the PTY. TI SEARCH button again. q After the name of the selected programme type has been lit for 2 seconds, "SEARCH" will appear, and the search operation will start. Note: If the programme type has changed from flashing to steadily lit and the PTY. TI SEARCH button is pressed, nothing will happen. Each time a station of the programme type you want is encountered, you will be able to listen to the broadcast. The channel number will flash for about 3 seconds. The station name will flash for 7 seconds, and then remain lit. q If you want to listen to another station of that programme type, press the PTY. TI SEARCH button whilst the channel number or station name is flashing. The unit will look for the next station of that type. Note: q If no station of the programme type you want can be found, "NOT FOUND" will appear for 4 seconds. 5 If you have selected the traffic programme: If you select traffic programme (TP) as the programme type in step 5, to receive only radio stations which broadcast traffic programmes, the TP will appear. (However, this does not necessarily mean that you will hear any traffic announcements at that time. ) When a traffic announcement is actually being made, the TA will appear. (When both the TP and TA will appear, an announcement is being made. ) 5 6 21 CD-C491H(SUK) TINSE0229AWZZ (Continued) Jog dial s To manually recall the stations stored in memory Each time you turn the jog dial one step the channel number will change. q After the channel number has been displayed for 2 seconds, the frequency for that channel will appear for 2 seconds, and then the station name will appear. s To switch the display: Each time the DISPLAY MODE button is pressed whilst an FM station is tuned in, the display will switch as follows: Station name (PS) Programme type (PTY) Frequency DISPLAY MODE When the station you are tuning in is not an RDS station or even if it is an RDS station but there is no station name or programme type information available, the display will switch as follows: "NO PS" "NO PTY" Frequency Notes: q "NO PS" or "NO PTY" will flash for about 5 seconds, and then the frequency will be displayed. q The display can only be switched whilst tuned to the FM band. s Notes for RDS operation If any of the following events occur, it does not mean that the unit is faulty. q "PS" and a station name appear alternately, and the unit does not operate properly. q If a particular station is not broadcasting properly or a station is conducting tests, the RDS reception function may not work properly. 22 CD-C491H(SUK) TINSE0229AWZZ (Continued) s EON-PTY PTY. TI SEARCH EON 1 2 3 4 Tune in the desired RDS station, then the PS name will be displayed. Press the EON button when "EON" appears. q "PTY. TI" and "SELECT" will appear alternately for about 4 seconds. Whilst they are being displayed, select the desired programme type turning the jog dial. [. . . ] q The batteries in the remote control are dead. q The remote control is being operated from an incorrect distance or angle. q The power cannot be turned on from the remote control. q "PROTECT" appears in the display, and no sound is heard. q Is the AC power lead plugged in? q Is the speaker wire shorted?q Was the unit used at high volume for many hours? q Plug in the speaker wire properly. [. . . ]