User manual SHARP CP-G10000

[. . . ] REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the lite rat ure ac company ing the appliance. Caution - use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. WARNING FCC Regulations state that any unauthorized changes or modifications to this equipment not expressly approved by the manufacturer could void the user's authority to operate this equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. [. . . ] q After the level is adjusted, stop the other equipment, and go to step 3. 12 4 0dB OVER 1 "PAUSE" indicator 1 Manual recording: 0dB Select the input, and then press the RECORD (REC) button. q The unit will enter the recording stand-by mode. q The space cut function will not work. 06 12 4 0dB OVER 1 Space cut function: q During sound synchro recording, if there are more than 3 seconds of silence in the playback sound, this unit will automatically enter the recording stand-by mode. ("SYNC STANDBY" will appear. ) Then, when further playback is started on the other equipment, this unit will resume recording. (A silence of up to 3 seconds can be created between tracks. ) q If there is noise between the tracks on the original recording, the sound synchro recording or space cut function may not work properly. q When recording tracks or sounds in which there are 3 seconds or more of very small continuous sounds that you want to record, use manual recording. 22 CP-G10000 (Continued) s Recording from the microphone INPUT SELECT RECORD REC LEVEL 1 2 3 4 Connect the stereo microphone to the MIC jack on the main unit. Press the INPUT SELECT button until "ANALOG" appears. Adjust the recording level using the REC LEVEL control. MIN MAX q The unit will enter the recording stand-by mode. MIC 5 6 q Adjust the recording level so that the maximum level does not exceed "0 dB". Press the MD 06 button. q Recording will start. To interrupt a recording: ENTER RECORD Press the MD button while recording. q The unit will enter the recording stand-by mode. q To resume recording, press the MD button again. When the power is turned off, the revised order will not be changed. (Page 29) 1 2 3 4 A 1 2 B 3 C 4 D 1 A 2 B 3 C 4 D A B C D C A B D COMBINE Two adjacent tracks (for example, the third and fourth tracks) can be combined. If there is a prolonged silent section in the middle of a selection that is recorded, a single piece of music may be recorded as two tracks. If this happens, these two tracks can be combined into a single track. (Page 28) Program move function This function allows the track numbers to be automatically rearranged in the order specified for programmed playback. The track numbers will be adjusted as needed, automatically. (The tracks that are not included in the programmed selections will be put at the end of the new track numbers. ) (Page 29) 1 2 3 4 1 2 3 4 A 1 2 B 3 C D 1 A 2 B 3 C 4 D A B C D C A D B ERASE Tracks you want to erase can be erased one at a time or all at once. Once a track has been erased, it cannot be recovered. Double-check the track number before erasing it. (Page 30) TRACK/DISC NAME You can assign titles to recorded tracks and to discs. The characters must be capital and lowercase letters, or symbols. [. . . ] There may be some deviations from these values in individual units. q General Type: Power source: Power consumption: Dimensions: Weight: MD/CD Deck AC 120 V, 60 Hz 20 W Width: 16-15/16" (430 mm) Height: 4-11/16" (118 mm) Depth: 11-15/16" (302 mm) 11. 3 lbs. (5. 1 kg) q MiniDisc recorder section Type: Signal readout: Audio channels: Frequency response: Rotation speed: Error correction: Coding: MiniDisc recorder Non-contact, 3-beam semi-conductor laser pick-up Stereo 2 channels/monaural (long-play mode) 1 channel 4 ­ 20, 000 Hz (+0/-1 dB) 400 ­ 900 rpm CLV, Approx. ACIRC (Advanced Cross Interleave Reed-Solomon Code) ATRAC (Adaptive TRansformed Acoustic Coding) Magnetic modulation overwrite method 1 bit 44. 1 kHz Unmeasurable (less than ±0. 001% W. 100 dB (1 kHz) 90 dB (1 kHz) 0. 008% Input jacks Jack name LINE IN Jack shape Pin jack Input impedance Over 22 kohms Reference input level 680 mVrms Minimum input level 170 mVrms Recording method: A/D, D/A converter: Sampling frequency: Wow and flutter: Signal/noise ratio: Dynamic range: T. H. D. [. . . ]