User manual SHARP CP-SW1000W

[. . . ] No objects filled with liquids, such as vases, shall be placed on the apparatus. Do not turn the volume on to full at switch on. Listen to music at moderate levels. Remote control x 1 Cleaning cloth x 1 General Information RCA cable (2 pins - 2 pins) x 1 RCA cable (1 pin - 2 pins) x 1 AC power lead x 1 AC power lead x 1 (for Saudi Arabia only) Features This subwoofer incorporates the Tymphany Linear Array Transducer ( LAT ) technology developed by Tymphany Corporation. This Technology uses a linear array of multiple smaller diaphragms to generate sound as opposed to the single diaphragm used in the conventional cone speakers. [. . . ] 8 TV Operation Buttons (Only SHARP TV): On/Stand-by Button Sets the TV Input Select power to Button (TV) "ON" or "STAND-BY". Channel Up and Down Buttons Press the button to switch the input source. Switch up/ down the TV channels. 1 Attach the foot cushions as shown Note: When attaching the foot cushions, place the subwoofer on a cushion or soft cloth to avoid damage. Vertical position Volume Up and Down Buttons 1 Place subwoofer stand as shown Note: Some models of SHARP TV may not be operable. Stand E-4 Preparation for Use CP-SW1000W Placing the subwoofer Installation image: TV Subwoofer connections to TVs Caution: Turn off all other equipment before making any connections. Notes: Refer to the operation manual of the equipment to be connected. Fully insert the plugs to avoid fuzzy pictures or noises. Caution: Tuner receiving for other audio system Placing the aerial near the subwoofer unit AC power lead may cause noise pick up. Place the aerial away from the subwoofer unit for better reception. ENGLISH VCR VCR DVD player DVD player Preparation for Use Connecting to a TV Place the subwoofer as shown. Notes: As the bass sound from the subwoofer is omni-directional, you can place the subwoofer anywhere you like. However, it is recommended to place it as close to the TV as possible. The front panel of the subwoofer is not removable. Caution: Do not change the installation direction when the subwoofer is turned on. Do not allow any objects to fall into or to be placed in the bass reflex ducts. Do not stand or sit on the subwoofer as you may be injured. If the TV/monitor has an audio output, connect it to the AUDIO INPUT sockets on the rear of the subwoofer. TV To audio output sockets Audio cable (supplied) To AUDIO INPUT sockets Subwoofer Magnetically shielded speakers The subwoofer can be placed near a TV set as the built-in speakers are magnetically shielded. However, uneven colours may appear on the screen depending on the type of TV. Turn off the TV (from the power switch). After 15 - 30 minutes, turn the TV on again. If the colour variation is still present. Move the subwoofer further away from the TV. Do not place the unit near any kind of magnet or an electromagnet as irregular colours may appear on the TV screen. E-5 AC power connection Connecting to a TV (with subwoofer pre-out) If the TV/monitor has subwoofer pre-out, connect it to the AUDIO INPUT sockets on the rear of the subwoofer. TV After checking all the connections have been made correctly, connect the AC power lead to the AC power input socket, then to the wall socket. CP-SW1000W ENGLISH Audio cable (supplied) To SUBWOOFER PRE-OUT socket Subwoofer Wall socket (AC 110 - 240 V ~ 50/60 Hz) Notes: Never use a power lead other than the one supplied. [. . . ] Wipe off any condensation on the transmitter with a soft cloth before operating the unit. CP-SW1000W Cleaning the cabinet Periodically wipe the cabinet with a soft cloth. Caution: Do not use chemicals for cleaning (petrol, paint thinner, etc. ). Do not apply oil to the inside of each component. It may cause malfunctions. ENGLISH If problem occurs When this product is subjected to strong external interference (mechanical shock, excessive static electricity, abnormal supply voltage due to lightning, etc. ) or if it is operated incorrectly, it may malfunction. [. . . ]