User manual SHARP CP-C250

[. . . ] CP-C250 CP-C250 Speaker System consisting of CP-C250 (front speaker system) and CP-SW10000S (active subwoofer). Accessories Please confirm that the following accessories are included. Remote control 1 (RRMCG0395AWSA) Red Black AM loop antenna 1 (QANTL0005AWZZ) Gray Black FM antenna 1 (92LFANT1746A) Wire for front speaker Wire for rear speaker Subwoofer cable 2 2 1 (QCNWHA003AWZZ) (QCNWHA004AWZZ) (QCNWGA003AWPZ) Note: Only the above accessories are included. CD-G10000 CP-C250 SPECIAL NOTES NOTE This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. [. . . ] Adding tracks to the program: If a program has been previously stored, the "MEMORY" indicator will be displayed. The new tracks will be stored after the last track of the original program. To check which tracks are programmed: While the unit is stopped in the programmed play mode, press the or button. Notes: When a disc with programmed tracks is ejected, the program is automatically canceled. Even if you press the ON/STAND-BY button to enter the stand-by mode or change the function from CD to another, the programmed selections will not be cleared. During the program operation, random play is not possible. During programmed play, the DIRECT PLAY button will not work. 2 Press one of the 1 - 5 buttons to select the desired disc. Selected disc number 3 Press the direct search buttons on the remote control to select the desired track. Selected track number You can also select a track by pressing the or button. 4 5 Press the MEMORY/SET (MEMORY) button to save the track number. If you make a mistake, the programmed tracks can be cleared by pressing the CLEAR/DIMMER button. Press the / button to start playback. 6 7 25 CD or MP3 disc Playback CD-G10000 CP-C250 MP3 navigation (only for MP3 files) MP3 navigation: You can search and play files by folder or title. For example, when you assign three titles to a file, enter genre (such as jazz) as title 1, album name as title 2, and music title as title 3 to search the file by any title. The unit searches for the same name within folders (or titles). 1 2 3 Perform steps 1 - 3 in "File search (by folder or title 1/2/3)" on page 27. Press the , , or button to select "FOL", "T-1", "T-2" or "T-3". To search files by folder name, select "FOL" (will flash). Folder Title 1 If the search word is not in the folder (or title) name, "NOT FOUND" appears and the menu returns. CD or MP3 disc Playback 9 Use the 10Press the or button to scroll and select a folder (or title). Title 2 Title 3 / button to start playback. All files in the selected folder (or title) are played, and the previous display returns. 4 Press the CHARACTER button for 2 seconds. The display will be ready for editing characters. 1st row: String table 2nd row: Input editor (8 digits) To exit the MP3 navigation mode: In the stop mode, press the button. Notes: The unit searches regardless of the case, and found names appear in uppercase. Character entry with direct buttons: The direct buttons on the remote control can also be used for character entry. In step 5 on the left, use buttons 0 9 to enter alphabets. Alphabet types change as you press a button. For example, press "2" four times to enter "C". 5 6 Press the Press the display. or or button to select the desired alphabet. [. . . ] Demagnetize these parts once every 30 hours of playing/recording time by using a commercial tape head demagnetizer. Read the demagnetizer's instructions carefully before use. 44 Specifications As part of our policy of continuous improvement, SHARP reserves the right to make design and specification changes for product improvement without prior notice. The performance specification figures indicated are nominal values of production units. There may be some deviations from these values in individual units. CD-G10000 CP-C250 Amplifier Output power Front speakers 135 watts minimum RMS per channel into 8 ohms from 100 Hz to 20 kHz, 10% total harmonic distortion Rear speakers 65 watts minimum RMS per channel into 16 ohms from 5 kHz to 20 kHz, 10% total harmonic distortion Output terminals Front speakers: 8 ohms Rear speakers: 16 ohms Headphones: 16 - 50 ohms (recommended: 32 ohms) Subwoofer pre-out (audio signal): 200 mV/10 k ohms at 70 Hz Video out: 1 Vp-p (75 ohms) Input terminals Game/ Auxiliary (audio signal): 500 mV/ 47 k ohms Game/Video: 1 Vp-p (75 ohms) General Power source Power consumption Dimensions AC 120 V, 60 Hz 175 W Width: 10-1/4" (260 mm) Height: 13" (330 mm) Depth: 12-7/8" (326 mm) 23. 0 lbs. [. . . ]