User manual SHARP CP-C770

[. . . ] Such arrangement enables: Powerful low bass without the need for large enclosures compared to the conventional speakers, hence the sleek and compact design of this subwoofer. Minimisation of structural vibrations which makes it possible to place the subwoofer close to your audio system without affecting the critical circuitry. AC power lead x 1 (for Taiwan only) Plug adaptor x 1 (for Saudi Arabia only) Plug adaptor x 1 (for Central and South America and Mexico only) Subwoofer stand x 2 E-1 Foot cushion x 4 Spike x 4 Contents Page Precautions General Please ensure that the equipment is positioned in a well-ventilated area and ensure that there is at least 10 cm (4") of free space along the sides, top and back of the equipment. 10 cm (4") 10 cm (4") 10 cm (4") CP-C770 ENGLISH General Information Precautions . . 3 - 4 Preparation for Use Subwoofer preparation. [. . . ] Warning: The voltage used must be the same as that specified on this unit. Using this product with a higher voltage other than that which is specified is dangerous and may result in a fire or other type of accident causing damage. SHARP will not be held responsible for any damage resulting from use of this unit with a voltage other than that which is specified. Controls and indicators ENGLISH 1 Front panel 2 3456 General Information Cooling fan This unit is fitted with a cooling fan at the rear for improved cooling. Do not cover the opening in this section with any obstacles. 8 Caution: The unit will get warm whilst being used. Do not touch the warm areas of the unit for prolonged periods to avoid injury. Volume control The sound level at a given volume setting depends on speaker efficiency, location, and various other factors. It is advisable to avoid exposure to high volume levels. Do not turn the volume on to full at switch on. Listen to music at moderate levels. 123 Rear panel Reference page 1. 5, 6 E-3 Subwoofer preparation 2 4 Make sure to unplug the AC power lead before installing the main unit or changing the position. Select from three installation methods according to the preferred position. Horizontal position Using spikes CP-C770 ENGLISH Remote control Plastic shie 3 1 Tighten all spikes as shown Battery holder Note: Before using remote control, please remove plastic shield at battery holder. Move the subwoofer further away from the TV. Do not place the unit near any kind of magnet or an electromagnet as irregular colours may appear on the TV screen. E-5 AC power connection Connecting to a TV (with subwoofer pre-out) If the TV/monitor has subwoofer pre-out, connect it to the AUDIO INPUT sockets on the rear of the subwoofer. TV After checking all the connections have been made correctly, connect the AC power lead to the AC power input socket, then to the wall socket. CP-C770 ENGLISH Audio cable (supplied) To SUBWOOFER PRE-OUT socket Subwoofer Wall socket (AC 110 - 240 V ~ 50/60 Hz) Notes: Never use a power lead other than the one supplied. Otherwise, a malfunction or an accident may occur. Unplug the AC power lead from the wall socket if the unit will not be in use for a prolonged period of time. E-6 Preparation for Use To AUDIO INPUT sockets CP-C770 Remote control Battery installation 1 Whilst pushing the locking tab towards the centre of the remote control, slide out the battery holder. Back of remote control Notes concerning use: Replace the battery if the operating distance is reduced or if the operation becomes erratic. Purchase "CR 2025", coin lithium battery. Periodically clean the transmitter on the remote control and the sensor on the unit with a soft cloth. Exposing the sensor on the unit to strong light may interfere with operation. Change the lighting or the direction of the unit if this occurs. Keep the remote control away from moisture, heat, shock, and vibrations. ENGLISH Locking tab 2 Remove the old battery from the battery holder, insert the new battery and then slide the battery holder back into the remote control. [. . . ] Before you switch on/off the subwoofer, minimise the volume on the audio system. Auto power off If no signal is detected for 20 minutes during power on, the subwoofer will automatically go to stand-by mode. (Turns red) E-8 Basic Operation Adjust the high frequency cut-off point. Frequencies higher than the set frequency are removed. To emphasise the bass, turn this control towards 80 Hz and increase the volume. CP-C770 ENGLISH Operating the TV with the remote control You can operate SHARP TV with this system's remote control. Troubleshooting chart Many potential problems can be resolved by the owner without calling a service technician. [. . . ]