User manual SHARP CP-C900H

[. . . ] (Even if the power is turned off, the battery will be drained slowly but continuously. ) RELEASE LOCK ­5­ CP-C900HH Error Messages ERROR MESSAGES BATT EMPTY BLANK MD q q MEANING The battery has run down. Nothing is recorded. ERROR MESSAGES Can'tSTAMP q MEANING Stamp function does not work. (Check the number of tracks. ) Can'tWRITE DEFECT! q (Replace the disc with a recorded disc. ) Can't COPY q You tried to record from a copy prohibited MiniDisc. Cannot save the TOC information correctly to a MiniDisc. The disc is scratched. q (Record using the analogue cable. ) q You tried to record signals other than music (such as data). DISC FULL Er-MD (**) (If the recorded sound is not right, retry recording or replace the disc with a recordable one. ) q q Can't EDIT q The disc is out of recording space. [. . . ] The microprocessor has reported a system fault and the unit is out of order. (Change the stop position of the track and then edit it. ) Can't PLAY Can't READ (*) q You tried to play back a track that cannot be played with this equipment. The disc data cannot be read because the disc is damaged. HOLD LOCKED (To have it repaired, go to the distributor where you purchased the unit. ) q q q The unit is in the hold mode. You removed a MiniDisc whilst recording or editing. (Reload the Minidisc or replace it with another one. ) Can't REC q Recording cannot be performed correctly due to vibration or shock. NO DISC (Turn off the power before removing the MiniDisc. ) q A disc has not been loaded. Number or symbol appears in (*) position. ERROR MESSAGES NO SIGNAL q q MEANING Poor connection of the digital cable. No output signal comes out from the connected unit to playback. ERROR MESSAGES TEMP OVER q MEANING The temperature is too high. (Turn off the power, and wait for a while. ) TOC FORM (**) q (Use the AC power for the connected unit. ) q q There is an error in the recording signal. The input signal has improper sampling frequency. You tried to record on a playback-only disc. The write protection tab of a MiniDisc is set to the protected position. You tried to record on a playback-only disc. Since a track number is currently being located or updated, the unit cannot accept your command. (Erase all of the tracks, and then record again. ) TOC FULL q PLAY MD PROTECTED There is no space left for recording character information (track names, disc names, etc. ). The track has been protected from being erased. q Tr. Has condensation formed inside the unit?Is the unit being influenced by mechanical shock or by static electricity? Is the battery exhausted?Is the unit being subjected to excessive vibration? The MiniDisc cannot be ejected. q Has the track number or character information been written on the disc yet?Is the unit in the recording or editing mode? q No sound is heard from the earphones. q q q Is the volume set too low?Are you trying to play a MiniDisc with data on it instead of a MiniDisc containing music? Recording and editing are impossible. q q q q q Is the MiniDisc protected against accidental erasure?Is the unit connected properly to the other equipment?Is the AC adaptor unplugged or did a power failure occur whilst recording or editing?Is an optical signal being output from the stereo system?Read the operation manual for the stereo system. When the operation buttons are pressed, the unit does not respond. q q q Is the unit in the hold mode?Is the earphones plug inserted firmly? ­7­ CP-C900HH 1 Insert a MiniDisc 2 4 3 Insert according to the direction arrow. 2 Connect the AC adaptor AC 230V, 50/60 Hz 1 To wall socket. 1 Slide the OPEN lever to release the compartment door. 3 Insert a MiniDisc as shown. 4 Close the compartment door. When you record on a MiniDisc, check that the erase prevention tab is set to the "recordable" position. [. . . ] 4 Close the compartment door. When you record on a MiniDisc, check that the erase prevention tab is set to the "recordable" position. To the DC IN 5V socket. 2 Lift it up. 1 Plug the AC adaptor into the wall socket. 2 Insert the plug on the other end into the DC IN 5V socket. Before using the unit with a rechargeable battery, the battery has to be charged. q When the unit is not in use for extended periods, remove the AC adaptor from the wall socket. Recordable Recording prevented 3 Connections s To connect to a stereo system with "LINE OUT" or "AUDIO OUT" sockets (Analogue connection) If the audio system has only one pair of sockets, they are usualy for input only and recording via this connection is not possible. Preparation for use The unit does not work if the HOLD button is set to HOLD. Remote control unit Move the HOLD switch to the safety position (direction indicated by the arrow). Orange mark Hold LINE IN To the DC IN 5V socket Press the HOLD button for 2 seconds or more. [. . . ]