User manual SHARP CP-F20H

[. . . ] Customers without internet access may telephone 08705 274277 during office hours (or (01) 676 0648 if telephoning from Ireland). *MD9000H(FRONT/BACK) 2 2001. 4. 20, 2:01 AM Special Notes NOTES FOR USERS IN THE U. K. AND IRELAND The mains lead of this product is fitted with a non-rewireable (moulded) plug incorporating a 3A fuse. Should the fuse need to be replaced, a BSI or ASTA approved BS 1362 fuse marked or and of the same rating as above, which is also indicated on the pin face of the plug must be used. Always refit the fuse cover after replacing the fuse. [. . . ] Music which has its roots in the musical culture of a particular nation, usually played on acoustic instruments. The narrative or story may be based on historical events of the people. CP-F20HH 1 2 RELIGION PHONE IN TRAVEL 3 INFO SPORT EDUCATE DRAMA CULTURE SCIENCE VARIED 4 - Using the Radio Data System (RDS) - 5 RDS Radio 6 7 NATION M POP M 8 OLDIES FOLK M ROCK M EASY M 9 DOCUMENT Programme concerned with factual matters, presented in an investigative style. NONE TP TA Broadcast when testing emergency broadcast equipment or receivers. Emergency announcement made under exceptional circumstances to give warning of events causing danger of general nature. Broadcasts which carry traffic announcements. Traffic announcements are being broadcast. 10 LIGHT M 11 CLASSICS OTHER M 12 WEATHER FINANCE CHILDREN Note: When you select a programme in the EON stand-by mode, the unit will display "TI" instead of "TA". Web-site: www. sharp. co. uk/support Help Line: 08705 274277 (office hours) 25 *MD9000H-E24-30 25 2001. 4. 20, 2:11 AM Using the Radio Data System (RDS) (continued) s Using the Auto Station Programme Memory To stop the ASPM operation before it is complete: Press the ASPM button whilst it is scanning for stations. The stations which are already stored in memory will be kept there. Notes: q If the same station is broadcasting on different frequencies, the strongest frequency will be stored in memory. q Any station which has the same frequency as the one stored in memory will not be stored. q If 40 stations have already been stored in memory, the scan will be aborted. If you want to redo the ASPM operation, erase the preset memory. (This does not mean that you can listen to the traffic information at that time. ) When a traffic information is broadcast, "TA" will appear. - Using the Radio Data System (RDS) - If you select the traffic programme: 4 5 3 RDS Radio Within 4 seconds, press the 5/3 or 2/4 button to select the programme type. 6 7 Each time the button is pressed, the programme type will appear. If the button is held down for more than 0. 5 seconds, the programme type will appear continuously. 8 4 Whilst the selected programme type is flashing (within 4 seconds), press the PTY. TI button again. 9 10 After the selected programme type has been lit for 2 seconds, "SEARCH" will appear, and the search operation will start. 11 12 Web-site: www. sharp. co. uk/support Help Line: 08705 274277 (office hours) 27 *MD9000H-E24-30 27 2001. 4. 20, 2:11 AM Using the Radio Data System (RDS) (continued) s To automatically play the desired programme (EON-PTY) When the desired type of programme is broadcast, the radio switches to it automatically. 5 When the specified programme starts on an ON (other network) station, the unit will automatically switch to the station and "PTY" will flash. 1 - Using the Radio Data System (RDS) - Tune in to an RDS station (when a station name is displayed). 6 2 Press the EON button when "EON" appears. When the programme is over, the unit will automatically return to the original station. Checking the stand-by mode setting: When in the EON stand-by mode, press the EON button. ("Programme type" ¡ "WAITING") RDS Radio q "PTY TI" will flash for about 4 seconds. q If the EON button is pressed when "EON" is not displayed, "NO EON" will To cancel the EON stand-by mode: When in the EON stand-by mode, press the EON button. ("PTY" will go out. ) appear for 4 seconds to indicate that the unit cannot enter the EON standby mode. 3 Whilst they are displayed, select the desired programme type by pressing the 5/3 or 2/4 button. The selected programme type will flash. 4 Within 4 seconds, press the PTY. TI button. q The selected programme type and "WAITING" will be displayed for 2 seconds each. q "PTY" will appear, and the unit will enter the EON-PTY stand-by mode. 28 *MD9000H-E24-30 Web-site: www. sharp. co. uk/support Help Line: 08705 274277 (office hours) 28 2001. 4. 20, 2:11 AM Using the Radio Data System (RDS) (continued) s To automatically play the traffic information (EON-TI) When the traffic information is broadcast, the radio switches to it automatically. CP-F20HH 1 5 When a TA specified starts on an ON (other network) station, the unit will automatically switch to that station, and "TI" will flash. 2 1 Tune in to an RDS station (when a station name is displayed). 3 2 - Using the Radio Data System (RDS) - 6 Press the EON button when "EON" appears. When the traffic information is over, the unit will automatically return to the original station. 4 5 Checking the stand-by mode setting: RDS Radio When in the EON stand-by mode, press the EON button. ("TI" ¡ "WAITING") To cancel the EON stand-by mode: q "PTY TI" will flash for about 4 seconds. q If the EON button is pressed when "EON" is not displayed, "NO EON" will 6 When in the EON stand-by mode, press the EON button. ("TI" will go out. ) 7 appear for 4 seconds to indicate that the unit cannot enter the EON standby mode. 8 3 Whilst they are displayed, select the TI (Traffic Information) by pressing the 5/3 or 2/4 button. 9 10 4 Within 4 seconds, press the PTY. [. . . ] After the "RESET" is displayed for about 1 second, the unit will enter the power stand-by mode. References s Cleaning the cabinet Periodically wipe the cabinet with a soft cloth and a diluted soap solution, then with a dry cloth. Caution: q Do not use chemicals for cleaning (petrol, paint thinner, etc. ). q Do not apply oil to the inside of the unit. It may cause malfunctions. Caution: This operation will erase all data stored in memory including clock, timer settings, tuner preset, and CD or MiniDisc programme. s Before transporting the unit Remove the CD and the MiniDisc from the unit. [. . . ]