User manual SHARP DV-5151S/5451S

[. . . ] · The following table describes the icons used in this Operation Manual. Icon Tips and Hints for easier operation Meaning DVD VIDEO CD Functions for DVD Functions for VIDEO CD CD Functions for Audio CD GENERAL INFORMATION CONNECTION AND INITIAL SETTING VCR, DVD SETUP WATCHING THE VCR, DVD OTHER INFORMATION Important! Be sure to read this Operation Manual carefully before using the Product for the first time, and keep it on hand for future reference when you experience operational problems. SAFETY INFORMATION GENERAL INFORMATION <Only for DV-NC70W/70> Note: This Product can be used only where the power supply is AC 110V-240V, 50/60Hz. <Only for DV-NC70X> Note: This Product can be used only where the power supply is AC 240V, 50Hz. It cannot be used elsewhere. · This Product is classified as a CLASS 1 LASER product. · The CLASS 1 LASER PRODUCT label is located on the rear cover. [. . . ] (The auto tracking control system engages and "|" flashes on the TV screen for a few seconds. ) | Press ËSTOP to stop playback. (If the tape reaches its end, the Product will automatically rewind the tape to the beginning, eject the cassette, and turn off the power. If a DVD is being played back, the power will not turn off. ) · NTSC tapes recorded in Hi-Fi and EP mode may appear distorted during playback. The tracking function can be used to slightly enhance the picture quality. DV- NC70W DV- NC70 DV- NC70X G-CODE PROG TIMER OPERATE ON/OFF EJECT DISPLAY VCR/DVD VCR MENU ON SCREEN SELECTOR DVD SETUP FUNCTION PROG/ CONTROL REPEAT ANGLE OPEN/ CLOSE TITLE CLEAR RETURN DVD MENU SET ENTER ZERO BACK SKIP SEARCH Video Search (with the Remote) AM/PM INPUT SELECT VCR DVD Use the following procedure to quickly find the section you want, while viewing the picture. / REV PLAY REC STOP TAPE SPEED DPSS SKIP AUDIO OUTPUT VCR DVD PAUSE/STILL FWD 1 During playback, press FFè for forward video search, or È REW for reverse search. There are 2 search speeds in each direction. The Product switches between them each time the button is pressed. Press ûPLAY to resume normal playback. · During video search of a tape recorded in the LP mode and EP mode, the upper part of the picture may be skewed to one side. TAPE SPEED VSF/VSR1 VSF/VSR2 PAL TAPE MESECAM TAPE PAL TAPE NTSC TAPE EP q q SLOW 2 CH VCR/DVD COMBINATION SP LP EP SP/LP 5 5 9 5 9 9 11 27 7 21 GB 52 VSF : Video Search Forward VSR : Video Search Reverse Playback Fast Forwarding and Rewinding 1 2 3 Press ËSTOP to stop the video tape. Press ËSTOP to stop fast forward/rewind. · If you use other than E-90/E-180 cassettes, fast forward and rewind may take somewhat longer. OPERATE EJECT/STOP REW PLAY/×2 REC CH AV 2 IN VIDEO L(MONO)-AUDIO-R TIMER PLAY STOP OPEN/CLOSE / VCR/DVD SELECTOR VCR DVD CH PLAY/ 2 REW EJECT / STOP DV- NC70W / G-CODE PROG Slow Motion Playback (with the Remote) DV- NC70 DV- NC70X 1 2 3 Press SLOW on the Remote during playback. TIMER OPERATE ON/OFF Press SLOW / (to the left of SLOW) to vary the slow motion playback speed between 1/5 and 1/30 of the normal playback speed. Press ûPLAY to resume normal playback. · No noise can be erased when a tape recorded in the NTSC SP mode is played back in special modes (still, slow motion, etc. ). However, this does not indicate a malfunction with the Product. · When the Product has been playing back an unrecorded section of tape, Poor Tracking and then reaches a recorded tape segment. When auto tracking engages, "|" on the TV screen flashes for a few seconds. | Normal tracking · When a poorly recorded tape is played back, auto tracking may not operate normally. In this event, manually adjust the tracking with CH ' / " to make any noise disappear. Quick Start with Full Loading Mechanism Your Product has a standby function (Full Loading Mechanism) to allow immediate recording and playback. After pressing ÆREC or ûPLAY, it takes about 2 seconds until recording or playback is engaged when in the standby mode. GB 54 Playback AUTO RENTAL (This function only works when AUTO RENTAL mode on the MODE selection screen is set to "ON". ) The convenient auto rental mode lets you enjoy playback with ease. When you insert a cassette with the erasure protection tab removed (rental videos, etc. ), your Product automatically turns on the power, rewind the tape forward to find the recorded section, and plays back the tape. When the tape reaches the end of recorded section, the Product automatically rewinds the tape, ejects it and turns off the power. If a DVD is being played back, the power will not turn off. DV- NC70W DV- NC70 DV- NC70X G-CODE PROG TIMER OPERATE ON/OFF EJECT 1 2 3 4 Press VCR MENU to display the menu screen. Press ' / " to select "MODE". Press ' / " to select "AUTO RENTAL". COLOUR AUTO PAL MESECAM NTSC NTSC 3. 58 4. 43 PAL TV BLUE BACK AUTO OFF AUTO RENTAL ON OFF REPEAT ON OFF NICAM AUTO OFF S. PICTURE ON OFF :SELECT :CHANGE SET:ENTER MENU:EXIT DISPLAY VCR/DVD VCR MENU ON SCREEN SELECTOR DVD SETUP FUNCTION PROG/ CONTROL REPEAT ANGLE OPEN/ CLOSE TITLE CLEAR RETURN DVD MENU SET ENTER ZERO BACK SKIP SEARCH AM/PM INPUT SELECT VCR DVD / REV PLAY REC STOP TAPE SPEED DPSS SKIP AUDIO OUTPUT VCR DVD PAUSE/STILL FWD 5 6 Press \ / | to select "ON" or "OFF". Press SET to confirm and then press VCR MENU to return to the normal screen. · If there is more than a 15 second unrecorded section between recorded sections, the tape will automatically stop and rewind. [. . . ] DVD has a structure consisting of two 0. 6 mm thin discs which are adhered to each other. Since the thinner the disc, the higher the density at which the information can be recorded, a DVD disc has a greater capacity than a single 1. 2 mm thick disc. Since the two thin discs are adhered to each other, there is the potential to achieve double-sided play sometime in the future for even longer duration play. Screen size that cuts off the top and bottom of the image to allow playing of Wide (16:9) software on a connected 4:3 TV. [. . . ]