User manual SHARP DV-700S

[. . . ] · The following table describes the icons used in this Operation Manual. Icon Tips and Hints for easier operation Meaning DVD Video Functions for DVD Video DVD-RW VIDEO MODE Functions for DVD-RW (Video Format Only) DVD-R Functions for DVD-R (Video Format Only) VIDEO CD Functions for VIDEO CD CD CD-R/RW Functions for Audio CD Functions for CD-R/RW GENERAL INFORMATION CONNECTION AND INITIAL SETTING VCR, DVD SETUP WATCHING THE VCR, DVD KARAOKE Function OTHER INFORMATION Important! Be sure to read this Operation Manual carefully before using the Product for the first time, and keep it on hand for future reference when you experience operational problems. DVNC85(E)#Hyo2. p65 3 03. 6. 24, 9:45 AM SAFETY INFORMATION GENERAL INFORMATION <Only for Hong Kong and Southeast Asia models> Note: This Product can be used only where the power supply is AC 110V-240V, 50/60Hz. <Only for Australia model> Note: This Product can be used only where the power supply is AC 230V-240V, 50Hz. It cannot be used elsewhere. · This Product is classified as a CLASS 1 LASER product. · The CLASS 1 LASER PRODUCT label is located on the rear cover. [. . . ] Press ûPLAY to resume normal playback. · No noise can be erased when a tape recorded in the NTSC SP mode is played back in special modes (still, slow motion, etc. ). However, this does not indicate a malfunction with the Product. · During slow motion, still picture, frame advance and double speed playback with a tape recorded in the PAL EP mode, noise may appear. DISPLAY VCR/DVD VCR MENU ON SCREEN SELECTOR DVD SETUP FUNCTION PROG/ CONTROL REPEAT ZOOM OPEN/ CLOSE TITLE CLEAR RETURN DVD MENU SET ENTER ZERO BACK SKIP SEARCH KARAOKE SELECT Still Picture and Frame Advance AM/PM INPUT SELECT VCR DVD / REV FWD PLAY REC STOP TAPE SPEED DPSS SKIP AUDIO OUTPUT VCR DVD PAUSE/STILL 1 2 3 4 5 Press âPAUSE/STILL during playback. This will freeze the picture on your TV. If noise bars appear on the screen during still picture, set your Product to the slow mode and press CH ' / " to make the noise disappear. If there is vertical jitter during still picture playback, press CH ' / " to stop jitter. Press âPAUSE/STILL during still mode for frame advance. Press ûPLAY again to resume normal playback. SLOW CH Double Speed Playback VCR/DVD COMBINATION 1 2 Press ûPLAY during playback. The tape will be played back at twice the normal speed. Press ûPLAY to resume normal playback. · Sound is muted during Video Search, Slow Motion, Still Picture, Frame Advance and Double Speed Playback. · To avoid damage to the tape, your Product will resume normal playback after about 5 minutes of slow motion playback and still picture. Press ' / " to select "AUTO RENTAL". COLOUR AUTO PAL MESECAM NTSC NTSC 3. 58 4. 43 PAL TV BLUE BACK AUTO OFF AUTO RENTAL ON OFF REPEAT ON OFF NICAM AUTO OFF S. PICTURE ON OFF :SELECT :CHANGE SET:ENTER MENU:EXIT DISPLAY ON VCR/DVD VCR MENU SCREEN SELECTOR DVD SETUP FUNCTION PROG/ CONTROL REPEAT ZOOM OPEN/ CLOSE TITLE CLEAR RETURN DVD MENU SET ENTER ZERO BACK SKIP SEARCH KARAOKE SELECT AM/PM INPUT SELECT VCR DVD / REV PLAY REC STOP TAPE SPEED DPSS SKIP AUDIO OUTPUT VCR DVD PAUSE/STILL FWD 5 6 Press \ / | to select "ON" or "OFF". Press SET to confirm and then press VCR MENU to return to the normal screen. · If there is more than a 15 second unrecorded section between recorded sections, the tape will automatically stop and rewind. To watch the next recorded section, press ËSTOP, fast forward to that section and play the tape. · If the erasure protection hole is covered, press ûPLAY after the power turns on automatically. (AUTO RENTAL Mode does not work. ) · The AUTO REPEAT mode has priority over the AUTO RENTAL mode. If the AUTO REPEAT mode is set to "ON" and the video cassette reaches its end, the Product will rewind the tape and play it back again without ejecting the tape or turning off the power. SLOW CH VCR/DVD COMBINATION COLOUR If the quality of a colour recording is poor, the picture may turn black and white. In this event, set the COLOUR mode on the MODE selection screen to PAL (fixed PAL colour mode), MESECAM (fixed MESECAM colour mode), NTSC (fixed NTSC mode). Normally, the colour mode should be set to "AUTO" mode. (See Mode Selection on page 25. ) 1 Follow steps 1 to 3 from "AUTO RENTAL" above. 57 DVNC85(E)#054_063. p65 57 03. 6. 24, 9:58 AM GB Playback 2 Press ' / " to select "COLOUR". COLOUR AUTO PAL MESECAM NTSC NTSC 3. 58 4. 43 PAL TV BLUE BACK AUTO OFF AUTO RENTAL ON OFF REPEAT ON OFF NICAM AUTO OFF S. PICTURE ON OFF :SELECT :CHANGE SET:ENTER MENU:EXIT Hong Kong model Southeast Asia model Australia model G-CODE PROG TIMER OPERATE ON/OFF EJECT 3 4 Press \ / | to select "AUTO", "PAL", "MESECAM" or "NTSC". Press SET to confirm and then press VCR MENU to return to the normal screen. · When the colour mode is set to fixed colour mode while the Product is playing back a black and white tape or is receiving a black and white broadcast, the picture may be coloured. In this event, set the COLOUR mode on the MODE selection screen to "AUTO" mode. DISPLAY ON VCR/DVD VCR MENU SCREEN SELECTOR DVD SETUP FUNCTION PROG/ CONTROL REPEAT ZOOM OPEN/ CLOSE TITLE CLEAR RETURN DVD MENU SET ENTER ZERO BACK SKIP SEARCH KARAOKE SELECT BLUE BACK This function eliminates monitor noise and mutes sound during playback of unrecorded portions of a tape, and when receiving a non-broadcasting channel. [. . . ] Since the thinner the disc, the higher the density at which the information can be recorded, a DVD disc has a greater capacity than a single 1. 2 mm thick disc. Since the two thin discs are adhered to each other, there is the potential to achieve double-sided play sometime in the future for even longer duration play. Processing performed by a DVD recorder and so forth that allows a DVD-RW/DVD-R disc recorded with a DVD recorder and so forth to be played with a playback-compatible device such as this product. Screen size that cuts off the top and bottom of the image to allow playing of Wide (16:9) software on a connected 4:3 TV. [. . . ]