User manual SHARP DV-HR350F

[. . . ] · Keep the AC power cord away from heating appliances. · Never put any heavy object on the AC power cord. · Do not bundle any cables such as; AC power cord, Round Coaxial cable or other cables that are used to connect this VCR/DVD to your TV together. The noise or disturbance of the picture may be generated. [. . . ] · Press Cursor { to go back one step from the current setting during steps 3 to 8. To Check, Correct, or Cancel a Timer Programme 1. Press TIMER ON/OFF then, VCR on the remote control. Press Cursor K / L to select the programme number which you want to check. The details of the programme will appear on the TV screen. · Press Cursor s / B to go to the digit you want to change. Then, enter correct numbers by pressing Cursor K / L. · You may cancel the entire programme by pressing Cursor s while the programme number flashes. Press TIMER ON/OFF to return to the timer standby mode. To Cancel a Timer Recording in Progress Press STOP C/EJECT A on the VCR/DVD. 4. Select the desired start time (hour & minute). or To decide. TIMER NUMBER 4 DATE 05/03 TU B START 11:__ __:__ END __ CHANNEL __ SPEED VPS/PDC OFF 5. All the DVD functions are available during OTR, timer standby mode and Timer Recording. · When you use the VCR/DVD in DVD mode during an OTR or a Timer Recording, the VCR/DVD will not turn off automatically even if the end time of the OTR or Timer Recording has been past. Note (for Timer Recording) : · If there is a power failure or the VCR/DVD is unplugged for more than 1 hour, clock and all timer settings will be lost. · If you want to use the VCR/DVD during a Timer Recording or while " " is on or flashing, Press OPERATE to turn on the VCR/DVD. Press DVD on the remote control to choose DVD mode, then continue with the other DVD features as described in this manual. You don't need to set the TIMER off to use the DVD. When an OTR or a Timer Recording is completed. . . · If the other Timer Recordings remain as programmed, the VCR/DVD switches to the DVD mode automatically, and the TIMER indicator on the front panel lights up to indicate the VCR/DVD is in the timer standby mode. In some occasions, however, the VCR/DVD may be automatically turned off, instead of changing to the DVD mode after pressing TIMER ON/OFF. To avoid overlap of Timer Programming . . . · A timer programme will not work while another programme is under execution. Programme 1 Programme 2 Programme 3 9:00 10:00 11:00 · The TIMER indicator on the front panel flashes if there are no more Timer Recordings on standby. If you want to use the VCR function, press TIMER ON/OFF on the remote control or STOP C/EJECT A on the VCR/ DVD. Then press VCR to activate the VCR function. Direct Dubbing VC R DVD 1 4 7 2 5 8 0 3 6 9 +10 P LAY S TOP press first. 4. Select the desired tape speed. SP VCR/DVD COMBINATION NA527AD Refer to page 7 to switch between the VCR mode and the DVD mode. This will be possible only if the DVD is not copy protected. 1. Insert a tape. · If necessary, rewind or fast forward the tape to the point at which you want to begin recording. Tape Type Tape S peed E -60 E -120 E -180 E -240 R ecording / P layback Time S P Mode LP Mode 1 hour 2 hours 2 hours 4 hours 3 hours 6 hours 4 hours 8 hours 5. Recording starts. with erase-protection tab 2. Insert a disc with label facing up. 6. Playback starts. 3. [. . . ] · This happens right after fast forwarding or rewinding. Audio or subtitle language does not · The selected language is not available for audio or subtitles on the DVD. The camera angle cannot be · The DVD does not contain sequences recorded from different camera angles. Audio or subtitle language cannot be · The DVD does not contain audio source or subtitles in the selected language. [. . . ]