User manual SHARP DV-NC100H

[. . . ] VCR/DVD COMBINATION MODEL DV-NC100H OPERATION MANUAL Please read this Operation Manual carefully before using your VCR/DVD COMBINATION. DV-NC100 OPERATE OPEN/CLOSE PULL OPEN REW FF STOP/ EJECT OUTPUT PLAY REC TIMER CH VCR DVD STOP PLAY (TRACKING) 2 The region number for this VCR/DVD is 2. VIDEO Plus+ and PlusCode are registered trademarks of Gemstar Development Corporation. The VIDEO Plus+ system is manufactured under license from Gemstar Development Corporation. If you require any advice or assistance regarding your Sharp product, please visit our web-site www. sharp. co. uk/customersupport. Customers without Internet access may telephone 08705 274277 during office hours (or (01) 6760648 if telephoning from Ireland). SAFETY INFORMATION WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE. TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, AND ANNOYING INTERFERENCE, USE THE RECOMMENDED ACCESSORIES ONLY. [. . . ] It will also be marked at the starting point of Timer recording and OTR. · The index mark is not recorded if STILL/PAUSE is pressed and released during recording. · The time gap between index marks on the tape should be greater than 1 minute for SP recording and 2 minutes for LP recording. 2 Press K or L repeatedly until the number of programmes that you want to skip appears. The VCR/DVD begins rewinding or fast forwarding to the beginning of desired programme. · When the preset programme is reached, the VCR/DVD will start playback automatically. NOTES: · Index Search can be set up to 20. · This function will not operate in the Recording mode. · Operations must be followed up within 30 seconds, from steps 2 to 3 . Otherwise the Index Search mode will be cancelled. · To exit the Index Search mode, press MENU in step 2 . Or press STOP after step 3 . Auto Return If there are any remaining programmes including Daily, Everyday and Weekly, AUTO RETURN will not operate. 2 Press K or L repeatedly to point to SET UP, then press B. 3 Press K or L to point to AUTO RETURN, then press B. Watch the Recorded TIMER PROGRAMME Press OPERATE to turn on the VCR/DVD, then press PLAY. ­ 17 ­ EN VCR OPERATION Time Search If a tape includes both programmes recorded in the PAL system and ones recorded in the NTSC system, this function may not be operated correctly. 2 Press K or L repeatedly until the desired time appears. The VCR/DVD begins rewinding or fast forwarding to the specified point. When 0:00 is reached, the VCR/DVD will start playback automatically. NOTES: · Time Search can be set up to 9 hours 59 minutes (9:59). · This function will not operate in the Recording mode. · Operations must be followed up within 30 seconds, from steps 2 to 3 . Otherwise the Time Search mode will be cancelled. [. . . ] · Some functions are prohibited on some discs. If you are unable to remedy a problem by following these hints, consult your dealer or service centre. ­ 29 ­ EN SPECIFICATIONS PRODUCT TYPE DVD Player with Video Cassette recorder NUMBER OF VIDEO HEADS 4 VIDEO SIGNAL STANDARD PAL colour system AUDIO RECORDING SYSTEM 1 Stationary head for liner audio 2 Rotary heads for Hi-Fi stereo CHANNEL COVERAGE IRA - E69 TIMER BACKUP 60 minutes DISCS (PLAYBACK COMPATIBILITY) DVD Video / Audio CD / Video CD / CD-RW / R DVD-RW / R, DVD+RW / R FREQUENCY RESPONSE DVD (linear sound) : 20 Hz to 20 kHz (sample rate: 48 kHz) 20 Hz to 44 kHz (sample rate: 96 kHz) CD : 20 Hz to 20 kHz SIGNAL-TO-NOISE RATIO (S/N RATIO) CD : 110 dB (JEITA) DYNAMIC RANGE DVD (linear sound) : 90 dB CD : 90 dB (JEITA) TOTAL DISTORTION FACTOR DVD : 1KHz 0. 008% (JEITA) CD : 1KHz 0. 008% (JEITA) WOW AND FLUTTER Below the measurement limitation (+/-0. 001% W PEAK) (JEITA) CONNECTIONS Front panel: RCA connector [ 1 Video input Audio input RCA connector [ 2 Rear panel: Audio/Video Output/Input 21-pin scart terminal [ 2 S-Video output Mini DIN 4-pin jack (75 ) Analog audio output RCA connector [ 2 (one left channel, one right channel) 2 Vrms (47 k) Coaxial digital audio output One pin jack, 500mVpp (75 ) POWER SOURCE 220-240 V ~ +/- 10%, 50Hz +/- 0. 5% POWER CONSUMPTION 30W (standby: 5W) OPERATING TEMPERATURE 5°C to 40°C DIMENSIONS W: 435mm H: 94mm D: 233mm WEIGHT Approx 3. 2kg · Designs and specifications are subject to change without notice. · If there is a discrepancy between languages, the default language will be English. MAINTENANCE Cleaning the Cabinet · Use a soft cloth slightly moistened with a mild detergent solution. Do not use a solution containing alcohol, spirits, ammonia or abrasives. Cleaning Discs · When a disc becomes dirty, clean it with a cleaning cloth. [. . . ]