User manual SHARP DV-NC230S(Y)

[. . . ] MODEL OPERATION MANUAL Please read this Operation Manual carefully before using your VCR/DVD COMBINATION. D V- N C 2 3 0 OPERATE OPEN/CLOSE PULL OPEN REW FF STOP/ EJECT OUTPUT PLAY REC TIMER (TRACKING) CH VCR DVD STOP PLAY 2 The region number for this VCR/DVD is 2. PAL ­1­ EN INFORMATION DVD FUNCTIONS VCR FUNCTIONS SETUP PREFACE DV-NC230S(Y) PRECAUTIONS VCR/DVD COMBINATION PRECAUTIONS SAFETY INFORMATION TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPARATUS TO DRIPPING OR SPLASHING, NO OBJECTS FILLED WITH LIQUIDS, SUCH AS VASES, SHOULD BE PLACED ON THE APPARATUS. Laser Diode Properties Material: GaAs Wave length: DVD: 655 nm CD: 790 nm Emission Duration: Continuous Laser output: Max. 0. 8 mW Power Cord Protection To avoid any malfunctions of the VCR/DVD, and to protect against electric shock, fire or personal injury, please observe the following. · Hold the plug firmly when connecting or disconnecting the AC power cord. [. . . ] · You may cancel the entire programme by pressing Cursor s while the programme number flashes. Press TIMER ON/OFF to return to the timer standby mode. To Cancel a Timer Recording in Progress Press STOP C/EJECT A on the VCR/DVD. 4. Select the desired start time (hour & minute). or To decide. TIMER NUMBER 4 DATE 05/03 TU B START 11:__ __:__ END __ CHANNEL __ SPEED VPS/PDC OFF 5. Repeat the procedure in step 4 to set the end time. Select the desired channel. or TIMER NUMBER 4 DATE 05/03 TU START 11:30 END 13:30 B CHANNEL P1 6 __ SPEED VPS/PDC OFF Hint · STOP C on the remote control will not function in the Timer Recording mode. To decide. 7. Select the desired recording speed. or TIMER NUMBER 4 DATE 05/03 TU START 11:30 END 13:30 CHANNEL P1 6 B SPEED SP VPS/PDC OFF 8. Select "VPS/PDC ON" or "OFF". or TIMER NUMBER 4 DATE 05/03 TU START 11:30 END 13:30 CHANNEL P1 6 SPEED SP B VPS/PDC ON · To set another programme after step 8, press Cursor B. To exit. The Video Programme System (VPS) or the Programme Delivery Control (PDC) is a very convenient system which assures that the TV programmes you have programmed for timer recording, will be recorded exactly from beginning to end, even if the actual broadcasting time differs from the scheduled time due to delayed start or extension of the programme duration. Also, if a programme is interrupted and, for example, some special news is broadcast, the recording will also be interrupted automatically and resumed when the programme continues. When the VPS/PDC signal drop out because the broadcast signal is weak, or when a broadcasting station does not transmit a regular VPS/ PDC signal, the timer recording will be performed in the normal mode (without VPS/PDC) even if it was programmed for VPS/PDC. When the starting time of the VPS/PDC timer recording is from 0:00 to 3:59 on a given day, the VPS/PDC function operates from 20:00 on the previous day to 4:00 on the following day. When the starting time of the VPS/PDC timer recording is from 4:00 to 23:59 on the given day, the VPS/PDC function operates from 0:00 on the day to 4:00 on the following day. This means that if the relevant programme is broadcasted within this period, it will be recorded correctly. If the timer is not programmed correctly, the incorrect timer setting stays in effect unless you cancel it. To cancel the incorrect timer setting, refer to "To Check, Correct, or Cancel a Timer Programme" above. HINTS FOR OTR AND TIMER RECORDING Before you set OTR or Timer Recording · If a tape is not in the VCR/DVD or does not have the erase-protection tab, the TIMER indicator on the front panel and " " flash and Timer Recording cannot be performed. · Press VCR on the remote control before you set Timer Recording. Make sure the remote control is in the VCR mode, then press TIMER ON/OFF. ·" " will not appear in the DVD mode. However, the Timer Recordings will remain as programmed. are available until TIMER ON/OFF is pressed. (OUTPUT on the front panel and VCR on the remote control will not function. ) · Once the VCR/DVD turns to the timer standby mode, no VCR functions · To cancel the timer standby mode, press TIMER ON/OFF on the remote control or STOP C/EJECT A on the VCR/DVD, then press VCR to activate the VCR function again. After an OTR and a Timer Recording has been set, this VCR/DVD operates as follows: · When Timer Recordings are set, the TIMER indicator on the front panel and " " will appear. To use the VCR as usual until the time for the recording, press TIMER ON/OFF so that the TIMER indicator on the front panel and " " disappear. [. . . ] "Prohibited icon" appears on the · That operation is prohibited by this VCR/DVD or the disc. screen, prohibiting an operation. Playback picture is partially noisy. INFORMATION · Some functions are not available in specific modes, but this is not a malfunction. Read the description in this Operation Manual for details on correct operations. · Playback from a desired track and random playback are not available during programmed playback. [. . . ]