User manual SHARP DV-NC70

[. . . ] VCR/DVD COMBINATION MODEL DV-NC70 OPERATION MANUAL OPERATE EJECT/STOP REW PLAY/×2 REC CH VCR/DVD SELECTOR TIMER VCR DVD PLAY STOP OPEN/CLOSE / AV 2 IN VIDEO L(MONO)-AUDIO-R PAL NTSC 2 NTSC/PAL About This Manual · All mentions of "the Remote" refer to the remote control unit. · The following table describes the icons used in this Operation Manual. Icon Tips and Hints for easier operation Meaning DVD VIDEO CD Functions for DVD Functions for VIDEO CD CD Functions for Audio CD GENERAL INFORMATION CONNECTION AND INITIAL SETTING VCR, DVD SETUP WATCHING THE VCR, DVD OTHER INFORMATION Important! Be sure to read this Operation Manual carefully before using the Product for the first time, and keep it on hand for future reference when you experience operational problems. SAFETY INFORMATION GENERAL INFORMATION Note: This Product can be used only where the power supply is AC 110V-240V, 50/60Hz. It cannot be used elsewhere. CAUTION: USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE. AS THE LASER BEAM USED IN THIS PRODUCT IS HARMFUL TO THE EYES, DO NOT ATTEMPT TO DISASSEMBLE THE CABINET. [. . . ] Do not force the cassette into the " apProduct. When the cassette has been properly loaded, " pears on the VCR Front Panel display. To remove the cassette, press EJECT during stop mode. OPERATE EJECT/STOP REW PLAY/×2 REC CH VCR/DVD SELECTOR TIMER VCR DVD PLAY STOP OPEN/CLOSE / AV 2 IN VIDEO L(MONO)-AUDIO-R PLAY/ 2 EJECT / STOP Playback 1 2 3 4 5 Switch on your TV and select the video channel. (The auto tracking control system engages and "|" flashes on the TV screen for a few seconds. ) | Press ËSTOP to stop playback. (If the tape reaches its end, the Product will automatically rewind the tape to the beginning, eject the cassette, and turn off the power. If a DVD is being played back, the power will not turn off. ) · NTSC tapes recorded in Hi-Fi and EP mode may appear distorted during playback. The tracking function can be used to slightly enhance the picture quality. TIMER OPERATE ON/OFF PROG EJECT DISPLAY ON VCR/DVD VCR MENU SCREEN SELECTOR DVD SETUP FUNCTION PROG/ CONTROL REPEAT ANGLE OPEN/ CLOSE TITLE CLEAR RETURN DVD MENU SET ENTER ZERO BACK SKIP SEARCH Video Search (with the Remote) AM/PM INPUT SELECT VCR DVD Use the following procedure to quickly find the section you want, while viewing the picture. / REV PLAY REC STOP TAPE SPEED DPSS SKIP AUDIO OUTPUT VCR DVD PAUSE/STILL FWD 1 During playback, press FFè for forward video search, or È REW for reverse search. There are 2 search speeds in each direction. The Product switches between them each time the button is pressed. Press ûPLAY to resume normal playback. SLOW 2 CH · During video search of a tape recorded in the LP mode and EP mode, the upper part of the picture may be skewed to one side. TAPE SPEED VSF/VSR1 VSF/VSR2 PAL TAPE MESECAM TAPE PAL TAPE NTSC TAPE EP G G VCR/DVD COMBINATION SP LP EP SP/LP 5 5 9 5 9 9 11 27 7 21 GB 52 VSF : Video Search Forward VSR : Video Search Reverse Playback Fast Forwarding and Rewinding 1 2 3 Press ËSTOP to stop the video tape. Press ËSTOP to stop fast forward/rewind. · If you use other than E-90/E-180 cassettes, fast forward and rewind may take somewhat longer. OPERATE EJECT/STOP REW PLAY/×2 REC CH AV 2 IN VIDEO L(MONO)-AUDIO-R TIMER PLAY STOP OPEN/CLOSE / VCR/DVD SELECTOR VCR DVD CH PLAY/ 2 REW EJECT / STOP / Slow Motion Playback (with the Remote) 1 2 3 Press SLOW on the Remote during playback. TIMER OPERATE ON/OFF Press SLOW / (to the left of SLOW) to vary the slow motion playback speed between 1/5 and 1/30 of the normal playback speed. Press ûPLAY to resume normal playback. · No noise can be erased when a tape recorded in the NTSC SP mode is played back in special modes (still, slow motion, etc. ). However, this does not indicate a malfunction with the Product. · During slow motion, still picture, frame advance and double speed playback with a tape recorded in the PAL EP mode, noise may appear. PROG EJECT DISPLAY ON VCR/DVD VCR MENU SCREEN SELECTOR DVD SETUP FUNCTION PROG/ CONTROL REPEAT ANGLE OPEN/ CLOSE TITLE CLEAR RETURN DVD MENU SET ENTER ZERO BACK SKIP SEARCH Still Picture and Frame Advance AM/PM INPUT SELECT VCR DVD 1 2 3 4 5 / Press âPAUSE/STILL during playback. This will freeze the picture on your TV. If noise bars appear on the screen during still picture, set your Product to the slow mode and press CH ' / " to make the noise disappear. If there is vertical jitter during still picture playback, press CH ' / " to stop jitter. Press âPAUSE/STILL during still mode for frame advance. Press ûPLAY again to resume normal playback. REV PLAY REC STOP TAPE SPEED DPSS SKIP AUDIO OUTPUT VCR DVD FWD PAUSE/STILL SLOW CH Double Speed Playback 1 2 Press ûPLAY during playback. The tape will be played back at twice the normal speed. Press ûPLAY to resume normal playback. VCR/DVD COMBINATION · Sound is muted during video search, slow motion, still picture, frame advance and double speed playback. [. . . ] Screen size that cuts off the top and bottom of the image to allow playing of Wide (16:9) software on a connected 4:3 TV. Linear PCM is a signal recording format used for audio CDs. The sound on audio CDs is recorded at 44. 1 kHz with 16 bits. (On DVD discs, sound is recorded at between 48 kHz with 16 bits and 96 kHz with 24 bits. ) Screen size that cuts off the sides of the image to allow playing of Wide (16:9) software on a connected 4:3 TV. [. . . ]