User manual SHARP DV-7036S

[. . . ] · Never put any heavy object on the AC power cord. · Do not attempt to repair or reconstruct the AC power cord in any way. CAUTION: USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE. AS THE LASER BEAM USED IN THIS VCR/DVD IS HARMFUL TO THE EYES, DO NOT ATTEMPT TO DISASSEMBLE THE CABINET. REFER SERVICING TO QUALIFIED PERSONNEL ONLY. WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE. [. . . ] Otherwise the Index Search mode will be cancelled. · To exit the Index Search mode, press MENU in step 2 . Or press STOP after step 3 . · · · · · Hints for Timer Recording If there is a power failure or the VCR/DVD is unplugged for more than 1 hour, clock and all timer settings will be lost. If a tape runs out before a timer recording is finished, the unit ejects the tape and switches into DVD mode automatically. Press TIMER ON/OFF to active VCR function. Once the unit goes into Timer-standby mode, no VCR functions are available until TIMER ON/OFF is pressed. (OUT PUT on the front panel and VCR on the remote control will not function. ) Press TIMER ON/OFF to activate VCR functions after your timer recording is finished. DVD functions are available during Timer-standby mode and Timer recording. You don't have to stop your timer recording. Time Search If a tape includes both programmes recorded in the PAL system and ones recorded in the NTSC system, this function may not be operated correctly. 2 Press K or L repeatedly until the desired time appears. The VCR/DVD begins rewinding or fast forwarding to the specified point. · When you want to cancel the Quick-Find while in progress, press STOP. · When the end of a tape is reached during the QuickFind, the tape will automatically rewind to the beginning. After rewinding finishes, the VCR/DVD will eject the tape. ­ 17 ­ EN VCR OPERATION Copying a Video Tape You can make copies of videotapes made by friends or relatives for your own enjoyment. WARNING: Unauthorised recordings of copyrighted video tapes may be an infringement of copyright laws. Connect the recording VCR/DVD (this unit), playing VCR (another VCR) and your TV as outline in the following diagram. [Source (Playing) VCR <Monaural>] (another VCR) to 21-pin scart terminal [TV set] (Use for monitoring) to aerial jack Video Cassette Tape This VCR/DVD will operate with any cassette that bears the VHS mark. For best results, we recommend the use of highquality tapes. Do not use poor quality or damaged tapes. · You can prevent accidental erasing of a recording by breaking off the erase-prevention tab on the back edge of the cassette. · If you decide to record on the tape again, cover the hole with plastic tape. DVD DIGITAL AUDIO OUT ANALOG AUDIO OUT S-VIDEO OUT AERIAL Round coaxial cable (supplied) VCR L AV2 (DECODER) AV1 (TV) RF OUT DVD/VCR Tab to RF OUT R [Editing (Recording) VCR/DVD] (this unit) Two Different Tape Speeds Before recording, select the tape speed : SP mode (Standard Play) or LP mode (Long Play). The table below shows the maximum recording/playback time using E-60, E-120, E-180 or E-240 tapes in each mode. 1 Insert a pre-recorded tape into the playing VCR. 2 Insert a tape with its erase prevention tab in place into the cassette compartment of the recording VCR/DVD. [. . . ] VCR/DVD does not respond to some ­Operations may not be permitted by the disc. VCR/DVD cannot not read CDs/DVDs ­Use a commonly available cleaning CD/DVD to clean the lens before sending the VCR/DVD for repair. ­Make sure the tape has a erase-prevention tab. ­Make sure this VCR/DVD is in VCR mode. [. . . ]