User manual SHARP DX-111H

[. . . ] There are only three wires to connect and four simple plug-in cables. Just follow the simple step-by-step instructions that follow. FEATURES l Remote mount changer holds up to 10 compact discs l Remote control with back-lit LCD panel, displays disc, track and function l Remote controls include forward and reverse track and disc search, track and disc scan, shuffle and repeat play plus high speed audible cue and review search l Advanced technology includes 8x oversampling digital filter and twin 1-bit digital/analog converters l The special design allows horizontal or vertical mounting. TOLL-FREEASSISTANCE The installation and connections are so simple we doubt you'll need our help, but if you do, we're here to help y u J s c l o r t l - r e a s s a c l n a 1-800-645-4994 during the days/hours shown. ut al u olfe sitne ie t TIME ZONE CENTRAL MOUNTAIN 6:30AM - 5PM 7AM - 3PM 7:30AM - 6PM 8AM - 4PM DAY MON. SATURDAY PACIFIC 5:30AM - 4PM 6AM - 2PM EASTERN 8:30AM - 7PM 9AM - 5PM INDEX Cnet . . . . . . . . . . . . . . . . . . . . [. . . ] . DRILL FOUR HOLES (2 EACH SIDE) 5/32" DIA. ) LOCKWASHER "G" (4 PCS. ) FLATWASHER "H" (4 PCS. ) CHECK UNDERNEATH BEFORE DRILLING! MOUNTING ONTO A FLAT VERTICAL SURFACE 1 . Using the changer with brackets attached as a template, mark two holes for each bracket attachment. Drill a 4mm (5/32") diameter hole at each of the four locations. eoe rlig Secure changer using four self-tapping screws "D", four flatwashers "H" and four lockwashers "G". Proceed to page 7! CHECK OPPOSITE BEFORE DRILLING! MOUNTING SURFACE 2 . 3 . DRILL FOUR HOLES (2 EACH SIDE) 5/32" DIA. (4mm. ) 4 . Note: If desired you can substitute the use of bolts and nuts for mounting either of the above methods by increasing the hole diameter to 1/4" diameter (6. 5mm) and use four pieces bolt "B" and four pieces hex nut "F". FLATWASHER "H" (4 PCS. ) LOCKWASHER "G" (4 PCS. ) SCREW "D" (4 PCS. ) Page 6 OVERALL WIRING VIEW This page is provided to give you a quick look at the entire wiring of the DX-111H. Use it to plan your wire routing paths and possible connection points. Detailed wiring is explained in the following pages. EXISTING CAR RADIO ANTENNA CABLE ANTENNA INPUT ANTENNA OUTPUT FM MODULE EXISTING CAR RADIO ANTENNA SOCKET GREEN/WHITE POWER WIRE CONNECT TO SOURCE OF CONSTANT +12 VOLTS BLACK EXISTING CAR STEREO ORANGE/WHITE WIRE GROUND WIRE CONNECT AT THE CAR'S FUSEBLOCK AT THE "RADIO" OR "ACCESSORY" IDENTIFIED TERMINALS REMOTE CONTROL DATA CABLE (15 FEET) REMOTE CONTROL CABLE (4-1/2 FEET) CHANGER NOTE: When routing wires and cables from the rear of the car to the dashboard, it is best to conceal the wires under carpeting. If you do not know how to do this, your local auto mechanic or car stereo installer should be consulted. Page 7 WIRING THE CD CHANGER There is one cable to connect the changer to the FM module as explained below. FM MODULE DATA CABLE The 15 foot data cable connects the changer to the FM module. First connect the end of the data cable labelled "TO CD CHANGER" to the socket on the left side of the changer. Never insert a damaged, warped, or dirty disc into the magaz n . ie 4 To remove a disc, depress the tab for the disc . slot you want to remove and gently slide the disc out of the magazine as shown. Note: Additional CD magazines are available (see page 1 of this manual). CD MAGAZINE LABEL SIDE UP (PLAYING SIDE DOWN) ONE DISC PER SLOT TO REMOVE DISCS 1. SLIDE DISC OUT LOADING THE MAGAZINE INTO THE CHANGER 1 Make certain all discs are fully inserted into the . 2 Slide the door on the changer fully to the right. 3 Position magazine as shown (top side facing . 4 Insert magazine into changer until it "clicks" in . 5 Slide the door of the changer fully closed. Note: The door of the changer must always be closed except when inserting or removing the magazine to prevent dust or dirt entry which could cause malfunctions. 6 To remove the magazine, slide the door fully to . [. . . ] It is equipped with a built in thermal protection circuit which will stop operation of the unit when the temperature reaches the pre-set level. If this should happen, the unit will resume operation when the vehicle returns to a normal temperature range. Remove the magazine from the unit when it is not being used during hot weather. If the discs are left in a extremely hot car they may warp. [. . . ]