User manual SHARP EC-S5170

[. . . ] MODELS EC-S5170 EC-T5180 EC-T5180A EC-T5180B OPERATION MANUAL VACUUM CLEANER CONTENTS PAGE · IMPORTANT SAFETY INSTRUCTIONS . . . . 2 · PARTS IDENTIFICATION . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 · SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 · OPERATING INSTRUCTIONS . . . . . . . . . . . . . . . . . . . [. . . ] Allow net filter assembly to completely dry before replacing it, then insert it into the dirt compartment. Net Filter Filter Assembly CAUTION: Do not use chemicals, bleach or hot water to clean the dirt compartment. Do not dry with hair dryer or heater. Fig. 25 HOW TO CLEAN THE MAIN FILTER 1 2 3 4 5 Hold the top handle glip, and release the filter clamp then remove the filter cover to open. Filter Cover Filter Clamp Remove main filter from the filter box and scrub the filter. (Fig. 34) Remove the lamp from the socket by pushing in gently and turning counterclockwise. 35) Install the new lamp by pushing it gently into the socket and turning clockwise. 35) Use any standard bayonet base vacuum cleaner lamp rated 125V, 20W. Replace the Lamp cover and secure with the screw. Lamp cover Fig. 33 Lift Fig. 34 2 1 2 1 Fig. 35 HOW TO REPLACE THE MAIN FILTER Basically, the main filter can be used throughout the life of the vacuum cleaner. If you chose to replace main filter, please refer to the maintenance instructions on page 12 which explain how to remove and replace filter. Filter Cover Filter Clamp Top Handle Grip Latch Portion Main Filter Fig. 36 15 REPLACEMENT INSTRUCTIONS HOW TO MAINTAIN OR REPLACE THE EXHAUST FILTERS The exhaust filter consists of an electrostatic HEPA Type filter. (EC-S5170) HEPA Filter (EC-T5180 series) The HEPA Type filter should be replaced at least every 10 months to maintain efficient filtration. (EC-S5170) HEPA Filter(EC-T5180 series) can be washed with running water. How to remove/set the filter. 1 2 3 4 5 6 Remove the dirt compartment. Exhaust Filter Case Unscrew the center screw. (Fig. 37) Lamp cover Fig. 37 Lift the lamp cover. (Fig. 37) Lift Lift the exhaust filter case. (Fig. 38) Fig. 38 At the botton of the case HEPA type filter (ECS5170) or HEPA filter(EC-T5180) is placed. HEPA Filter (EC-T5180 series) can be washed with running water. After washing it, please dry completely in the air. Do not use hair dryer or other heating machine. Fig. 39 Filter case 7 8 16 Replace the filter as before and set the filter case and lamp cover. HEPA filter (EC-T5180 series) HEPA Type Filter (EC-S5170) (Replace type) Secure the center screw. Show Green Net Side Fig. 40 HOW TO REPLACE THE BELT AND OR AGITATOR ASSEMBLY When replacing the belt, always set the RUG/FLOOR Selector pedal in the "FLOOR" position. 1 After removing the bottom plate (see page 13) to determine if the belt or the agitator is worn or broken. Motor Shaft 2 3 Pull out the agitator and then remove the flat belt from the motor shaft. 42) Flat Belt Agitator Assembly Loop the (new) belt around the motor shaft and (new) agitator as shown. 42) Main Pulley Idler Pulley Idler Pulley Flat Belt Fig. 41 Main Pulley 4 Then re-insert the (new) agitator assembly, making sure that both ends of the agitator assembly fit in the groove of the nozzle head. 43) Be sure to install the new flat belt into the belt guide properly. 43) Motor Shaft Arrow (To insert the agitator assembly into the nozzle head, follow the Arrow direction as indicated. ) Fig. 42 5 Be sure that the flat belt is not twisted and all rotating parts move smoothly. (Fig. 43) And secure the bottom plate with four screws. (see page 13) Belt Guide Agitator Groove Fig. 43 17 BEFORE REQUESTING SERVICE If you experience any difficulties with your vacuum cleaner, use this Troubleshooting Chart first before requesting service. NOTE: Always remember to have the vacuum cleaner turned OFF and disconnect the plug from the power outlet before working on the vacuum cleaner. TROUBLESHOOTING CHART Problem Motor does not start when the power switch is in the ON position. The agitator does not rotate when the power switch is in the ON position. Suction power is weak or decreases suddenly. Check Check if the power cord plug is completely inserted into the outlet. [. . . ] Compruebe la cabeza de la boquilla, manguera de succi n, etc. , para ver si hay obstrucci n. Remedio posible Inserte bien la clavija en el tomacorriente. Reemplace la correa plana o inst lela correctamente. Extraiga los objetos extran s que pueden haberse atascado en la cabeza de la boquilla, manguera de succi n, etc. SERVICIO AL CONSUMIDOR POR TELEFONO: Disque 1-800-BE-SHARP (1-800-237-4277) por: SERVICIO (por el Servicio Autorizado Sharp más cercano) REPUESTOS (por el Distribuidor de Repuestos más cercano) ACCESORIOS INFORMACION ADICIONAL POR ESCRITO: Por problemas de funcionamiento, información acerca de la garantía, unidades incompletas u otro tipo de consultas. Sharp Electronics Corporation Customer Assistance Center 1300 Naperville Drive Romeoville, IL 60446-1091 Cuando nos llame o escriba suministrenos la siguiente información: modelo, número de serie, fecha de compra, su dirección (incluyendo el código postal), un teléfono donde podamos llamarle durante el día (incluyendo el código del area) y la descripción del problema. 22 DESCRIPCION DE LOS ACCESORIOS Para reemplazo de accesorios, por favor contacte a su distribuidor Sharp mas cercano. Liame al 1-800-642-2122, o visite nuestra pagina de internet (http://www. sharp-usa. com) ARTICULO 1 2 3 4 DESCRIPCION ARTICULO CORREA PLANA FILTRO DE RESCARGA (EC-S5170) FILTRO PRINCIPAL NUMERO DE PARTE EC-02BU3 (2 Piezas en 1 Paquete ) EC-01MU14 ( EC-01MU12 ) ) FILTRO DE RESCARGA (EC-T5180 serie) EC-01MU13 ( Para Partes, por favor contacte a su distribuidor Sharp mas cercano, si su distribuidor no posee Las partes que usted requiere, deberá pedirlas llamando al 1-800-BE-SHARP. ARTICULO 5 6 7 8 9 10 11 12 DESCRIPCION ARTICULO LAMPARA TURBO EXTENTION (INTERIOR) TURBO EXTENTION (IEXTERIOR) TUBO PARAHENDIDURAS ENSAMBLE DE AGITATOR HERRAMIENTA PARA TAPICERIA CEPILLO FILTRO DE RED NUMERO DE PARTE RLMP-A003VBE0 PPIPPA164VBFC PPIPPA163VBFE UCATSA057VBFE DRTR-A018VBKZ FCAT-A102VBKZ PBRS-A061VBEB FDUC-A019VBKA 1 2 3 4 5 6 7 8 9 10 11 12 23 GARANTIA LIMITADA SHARP ELECTRONICS CORPORATION garantiza al primer comprador del producto que este producto de marca Sharp (el "Producto"), cuando es embarcado en su recipiente original, está libre de materiales y fabricación defectuosa y acorda que a su opción, reparará el defecto o reemplazará el producto o la parte defectuosa sin cargar al comprador las partes o trabajo durante el periodo(s) de tiempo establecido abajo. [. . . ]