User manual SHARP ER-A220

[. . . ] ELECTRONIC CASH REGISTER ELEKTRONISCHE REGISTRIERKASSE CAISSE ENREGISTREUSE ELECTRONIQUE CAJA REGISTRADORA ELECTRONICA MODEL MODELL MODELE MODELO ER-A220 INSTRUCTION MANUAL BEDIENUNGSANLEITUNG MANUEL D'INSTRUCTIONS MANUAL DE INSTRUCCIONES ER -A 22 0 CAUTION: The cash register and the remote drawer should be securely fitted to the supporting platforms to avoid instability when the drawers are open. CAUTION: The socket-outlet shall be installed near the equipment and shall be easily accessible. VORSICHT: Die Netzsteckdose mu nahe dem Gert angebracht und leicht zugnglich sein. ATTENTION: La prise de courant murale devra tre installe a proximit de l'quipement et devra tre facilement accessible. [. . . ] Setting "printing" for a PGM function "Printing exchange total amount and change amount on receipt or journal" 5. Setting "multiplication" for a PGM function "Exchange calculation method" 6. Changing the domestic currency symbol to the EURO symbol ( ) and setting the number of digits after decimal point of the domestic currency amount to 2 7. For the setting of the currency symbol and the number of digits after decimal point of exchange amount, the ones that had been set to the domestic currency are set. Setting the round-off function for currency exchange After the execution of the procedure with the substitution of "2", treat EURO as domestic currency, and national currency as foreign currency using the exchange key (e) with the preset rate entry. Since EURO becomes domestic currency in your register after execution of the procedure with the substitution of "2", you must change unit prices in each department and PLU to make prices correspond to EURO before actually you start operating your register again. As for the miscellaneous keys, also please change the rates or amounts so that they are based on amounts in EURO. 37 When "3" is substituted to "A": 1. Resetting GT1, GT2, GT3 and Training GT 4. Setting "not printing" for a PGM function "Printing exchange total amount and change amount on receipt or journal" 5. Setting "multiplication" for a PGM function "Exchange calculation method" 6. Changing the domestic currency symbol to the EURO symbol ( ) and setting the number of digits after decimal of the domestic currency amount to 2 7. Setting the round-off function for currency exchange After the execution of the procedure with the substitution of "3", treat EURO as domestic currency. When the operation with the substitution of "2" has been performed already, "3. Resetting GT1, GT2, GT3 and Training GT" is not executed. When the operation with the substitution of "1" or "2" has been performed already, the currency symbol of exchange key is overwritten with a space. If you want to check the current status you are in, set the manager key (MA) to X2/Z2 position, and use the following sequence. 800 Optional Programming for the Introduction of EURO Some programming relating with the function of exchange key (e) cannot be changed automatically with the execution of modification operation described in the previous section. After the execution on each period, conduct the following programming depending on your needs. Programming for Exchange Key (e) Currency exchange rate For period 1 and period 2, set the EURO conversion rate. For programming details, refer to "Programming the rate". Exchange rate entry selection When you treat EURO currency in the exchange key, you must apply preset rate entry. So, make enable for preset rate entry for period 1 and period 2. For programming details, refer to "Programming function parameters for e key". Cheque/credit operation For period 1 and period 2, enable cheque/credit operation when tendering in foreign currency so that you can treat cheque and credit for EURO currency and national currency. [. . . ] Press the key and continue the operation. Action 59 LIST OF OPTIONS For your register, the following options are available. Remote drawer model ER-05DW and ER-06DW Till model ER-58CC for ER-05DW Coin case model ER-58CV for ER-05DW Key kit models By using the following key kits, you can change the keyboard layout of your register. ER-11KT7: 30 regular size key kits ER-12KT7: 30 1 x 2 size key kits ER-22KT7: 10 2 x 2 size key kits ER-11DK7G: 30 regular size dummy key kits ER-51DK7G: 10 5 x 1 size dummy key kits SPECIFICATIONS Model: Dimensions: Weight: Power source: Power consumption: Working temperature: Electronics: Built-in battery: Display: Operator display: Customer display: Printer: Type: Printing speed: Printing capacity: Other functions: ER-A220 330 (W) x 363 (D) x 238 (H) mm 8. 9 kg Official (nominal) voltage and frequency Stand-by 20W Operating 45W (max. ) 0 C to 40 C LSI (CPU) etc. [. . . ]