User manual SHARP ER-4110S

[. . . ] Other items may be prohibited by local law. Money Stamps Bonds Stocks Bank drafts Checks Passports Driver's licenses CAUTIONS Caution label on the unit The label ( ) in the fusing area of the unit indicates the following: : Caution, risk of danger : Caution, hot surface Cautions on using Follow the cautions below when using this unit. Warning: · The fusing area is hot. Exercise care in this area when removing misfed paper. · Do not look directly at the light source. [. . . ] Remove the misfed Misfeed indicator Blinking paper referring to the description of "MISFEED REMOVAL". An original misfeed has occurred in the SPF. SPF misfeed Blinking Remove the misfed originals referring to the indicator description of "D: Misfeed in the SPF". Press any key to cancel the preheat mode. Power save indicator is The unit is in the auto power shut-off mode. Press the start ( ) key to cancel the auto power shut-off mode. "CH" is blinking in the display. The paper tray is not installed properly. Push the tray into the unit securely. Indication Page 70 58 70 57 63 67 54 54 ­ 57 ­ 15, 17 63 The TD cartridge is not installed. Close the side cover "CH" is steadily lit in the securely by pressing the round projections near display. The paper tray or multi-bypass tray is empty. Doing so may damage the drum and cause smudges on copies. · If the paper has been fed through the multi-bypass tray, do not remove the misfed paper through the multi-bypass tray. Toner on the paper may stain the paper transport area, resulting in smudges on copies. 2 Close the side cover by pressing the round projections near the side cover open button. The misfeed ( ) indicator will go out and the start ( ) indicator will light up. 64 B: Misfeed in the fusing area 1 Lower the fusing unit release lever. Fusing unit release lever 2 Gently remove the misfed paper from under the fusing unit as shown in the illustration. If the paper cannot be removed, proceed to "C: Misfeed in the transport area". The fusing unit is hot. Do not touch the fusing unit when removing misfed paper. Doing so may cause a burn or other injury. · Do not touch the surface of the drum (green portion) of the drum cartridge when removing the misfed paper. · Do not remove the misfed paper from above the fusing unit. Unfixed toner on the paper may stain the paper transport area, resulting in smudges on copies. 3 Raise the fusing unit release lever and then close the side cover by pressing the round projections near the side cover open button. The misfeed ( ) indicator will go out and the start ( ) indicator will light up. 8 65 C: Misfeed in the transport area 1 2 3 Lower the fusing unit release lever. See "B: Misfeed in the fusing area" (p. 65). Open the front cover. To open the front cover, see "INSTALLING THE TD CARTRIDGE" (p. 10). Rotate the roller rotating knob in the direction of the arrow and gently remove the misfed paper from the exit area. Roller rotating knob 4 Raise the fusing unit release lever, close the front cover and then close the side cover by pressing the round projections near the side cover open button. [. . . ] 51 Setting the copy quality - AUTO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 - MANUAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49 - PHOTO. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49 Setting the copy quantity . . . . . . . . . . . . . . . . . . . [. . . ]