User manual SHARP ER-4700

[. . . ] AVISO: El tomacorriente debe estar instalado cerca del equipo y debe quedar bien accesible. VARNING: Det matande vgguttaget skall placeras nra apparaten och vara ltt atkomligt. CAUTION: For a complete electrical disconnection pull out the mains plug. VORSICHT: Zur vollstndigen elektrischen Trennung vom Netz den Netzstecker ziehen. [. . . ] According to the steps of the introduction, you can make your register correspond to EURO. Set the manager key (MA) to X2/Z2 position, and use the following sequence. 800 . *A *A=1: Applicable for period 1 *A=2: Applicable for period 2 *A=3: Applicable for period 3 You can perform each operation only once with the substitution of "A=1", "A=2" and "A=3". If you perform the operation with the substitution of "A=2" first, you cannot perform the operation with the substitution of "A=1". If you perform the operation with the substitution of "A=3" first, you cannot perform the operation with the substitution of "A=1" and "A=2". The details of the automatic register system modification are as follows: (As for PGM functions described below, please refer to "Programming EURO system settings" for "Printing exchange total amount and change amount on receipt or journal" and "Exchange calculation method", "Programming function parameters for e key" for the number of digits after decimal point of exchange amount, "Programming exchange currency symbol" for exchange currency symbol, and "Programming domestic currency symbol" for domestic currency symbol. ) When "1" is substituted to "A": 1. Setting "printing" for a PGM function "Printing exchange total amount and change amount on receipt or journal" 4. Setting "division" for a PGM function "Exchange calculation method" 5. Setting the EURO symbol ( ) for the currency symbol of exchange key, and setting "2" for the number of digits after decimal point of exchange amount 6. Setting the round-off function for currency exchange After the execution of the procedure with the substitution of "1", treat EURO as foreign currency using the exchange key (e) with the preset rate entry. When "2" is substituted to "A": 1. Resetting GT1, GT2, GT3 and Training GT 4. For programming details, refer to "Programming EURO system setting". 38 OVERRIDE ENTRIES Programmed limit for functions (such as for maximum amounts) can be overridden by making an entry in the MGR mode. 1. 2. Turn the mode switch to the MGR position. Make an override entry. On this example, the register has been programmed not to allow deduction entries over 1. 00. Key operation example Print REG-mode entries 1500 250 - . . . Error c Turn the mode switch to the MGR position. 250 Return the mode switch to the REG position. CORRECTION AFTER FINALIZING A TRANSACTION (AFTER GENERATING A RECEIPT) When you need to void incorrect entries that cashiers cannot correct (incorrect entries that are found after finalizing a transaction or cannot be corrected by direct or indirect void), follow this procedure. 1. 2. Turn the mode switch to the position using the manager key (MA). Repeat the entries that are recorded on an incorrect receipt. (All data for the incorrect receipt are removed from register memory; the voided amounts are added to the void-mode transaction totalizer. ) Incorrect receipt Cancellation receipt 39 FOR THE OPERATOR PRIOR TO ENTRIES 1 Preparations for entries Before registrations, insert the operator key into the mode switch and turn it to the REG position and check the following items: Paper roll If the paper roll is not set in the machine or there is low roll, install new one according to section "4. Installing and removing the paper roll" under "OPERATOR MAINTENANCE. " Bill separator A bill separator is set in a drawer. When necessary, use the separator so that you can treat two kinds of bills in a bill case. Receipt ON/OFF function When you use the printer to issue receipts, you can disable receipt printing in the REG mode to save paper using the receipt function. To disable receipt printing, press the key in the OP X/Z position. [. . . ] Compulsory depression of the key for direct finalization Compulsory tendering Overlapped cashier error Cashier resetting over error No entry of a cashier code Overflow limitation error The open price entry is inhibited. Make a registration within a limit of entry. Finalize the transaction, and correct the wrong entries in the void mode. Enter a correct code, or declare it by the programming. [. . . ]