User manual SHARP ER-A5IN

[. . . ] AVISO: El tomacorriente debe estar instalado cerca del equipo y debe quedar bien accesible. VARNING: Det matande vägguttaget skall placeras nära apparaten och vara lätt atkomligt. CAUTION: For a complete electrical disconnection pull out the mains plug. VORSICHT: Zur vollständigen elektrischen Trennung vom Netz den Netzstecker ziehen. [. . . ] 11 NILS : ; 55 10 Programming various functions Programming for optional feature selection PGM 2 2616 OP X/Z mode availability When a cashier needs to take the cashier/clerk X or Z report, he or she will use the OP X/Z mode. This programming determines whether he or she will be allowed to use this mode. Note You can take cashier/clerk X and Z reports in the X1/Z1 mode regardless of the above programming. Paid out in the REG-mode Refund key in the REG-mode Direct void in the REG-mode Indirect void in the REG-mode Subtotal void in the REG-mode First item direct void Printing of the number of purchased items Journal print form You may choose either of the following forms. · Detailed journal print that shows the details of all entries - the same information as printed on the receipt. · Summary journal print that shows information about all entries other than normal department entries (entries into "+" departments and their associated "+" PLUs). Zero skip for various reports VAT/tax amount, taxable amount and net amount printing on the receipt/journal VAT shift type VAT shift by cashier: VAT shift is performed by the operation of a cashier who has been assigned to do the VAT shift operation (Refer to job# 2510). VAT shift by shift key: VAT shift is performed by pressing the VAT shift key. No sale in REG-mode Finalization when the subtotal amount is zero in the REG mode Printing of the exchange 1 total amount and change amount on the receipt/journal Total and change amounts in exchange 1 currency are printed respectively below each of the total and exchange amounts in domestic currency. Footer graphic logo printing Credit counting when received-on-account/paid out finalized with the credit key Separator line in the report Link PLU printing on the receipt Procedure To keep the current setting 2616 ** P (1 to 13) The current setting is displayed. . *ABCDEFGH : ; 56 **P: 1 * Item: A B C D E F G H OP X/Z mode Paid-out in REG-mode Always enter 0. Refund key entry in the REG-mode Direct void in the REG-mode Indirect void in the REG-mode Subtotal void in the REG-mode Always enter 0. Selection: Enable Disable Enable Disable Enable Disable Enable Disable Enable Disable Enable Disable Entry: 0 1 0 1 0 0 1 0 1 0 1 0 1 0 **P: 2 * Item: A The first item direct void Selection: Enable Disable No Yes Detailed Limited B and C Always enter 0. D Printing of the number of purchased items E F Always enter 0. Journal print form G and H Always enter 0. Entry: 0 1 0 0 1 0 0 1 0 **P: 3 * Item: A B C D E F G H Selection: Always enter 0. 00 10 13 20 27 29 30 31 32 40 50 60 70 Report General report Full department report Full department group report PLU report PLU zero sales report PLU price category report Transaction report Total in drawer report Commission sales report Full clerk report Full cashier report Hourly sales information Daily net report Range report is available only in the X1 mode. X1/X2 mode only *3 Start time/end time (0 through 2330) X1/X2 mode only X1/X2 mode only X1/X2 mode only X1/X2 mode only *3 Start price amount/end price amount X1/X2 mode only X1/X2 mode only *3 Start PLU code/end PLU code (1 through 999999) Available mode *2 Range parameter *3: Both range setting and full setting are allowed. Note When Z of stacked report is initiated, X only reports will be skipped. Example Key operation Print 2620 . 10 : 13 : ; 61 Setting the time range for hourly reports You can set the time range for an hourly report. PGM 2 2619 Procedure When A through C are all zeros 2619 . * ABC ; *A: Time range To set the time range to 30 minutes (in the 24-hour system), enter 0. To set the time range to 60 minutes (in the 24-hour system), enter 1. BC: Starting time (hour = 00 to 23) Example Key operation Print 2619 . 107 ; Note To perform this setting, an hourly Z report (# 160) must be done. PGM 2 RS-232C channel assignment 2690 Your machine is equipped with an RS-232C interface. If you use the on-line communication function, the channel number of the RS-232C interface must be programmed by using the following procedure. To realize the on-line communication, consult your dealer. Procedure When A through D are all zeroes 2690 . *P 1 to 3 **ABCD : ; Entry: 0 8 0 *P: 1 ** Item: A B to D For the ON-LINE communication Always enter 0. Selection: Disable Enable (enter the channel number) *P: 2 and 3 (ABCD: Not used. Always enter 0. ) Example Key operation Print 2690 . 1: ; P A through D 62 Secret codes to control access to PGM1 mode, X1/Z1 mode and X2/Z2 2631 2632 mode PGM 2 2630 You must enter a secret code according to the following procedure before performing any PGM1-mode, X1/Z1mode or X2/Z2-mode operation when a secret code has been set for that specific mode operation. Operating Procedure ; Note Secret code Max. [. . . ] Replace a journal paper roll with a new one. Expand the file within a capacity of memory. Press the : key and continue the operation. Make a tendering operation. Enter a non-add code. [. . . ]