User manual SHARP ERA750 LINE OPERATION MANUAL

[. . . ] POS TERMINAL MODEL ER-A750 INTER-REGISTER COMMUNICATION SYSTEM INSTRUCTION MANUAL TABLE OF CONTENTS Page Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 3 4 4 5 6 6 7 8 9 10 11 13 13 14 17 17 18 18 19 19 20 21 22 23 23 24 25 26 26 26 27 28 29 30 31 32 1 IRC Programming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Setting machine numbers -- master and satellite. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Setting terminal numbers (IRC machine numbers) -- master and satellite . . . . . . . . . . . . . . . . . . . Creating/updating the master list -- master. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] The data in the clerk file at each satellite will be collected by the master when a consolidated report is issued. (3) Notes on the IRC system that uses the overlapped clerk system · If the overlapped clerk system is used, the clerk file must be allocated on the individual file allocation system. · When an initial entry is made at a satellite, additional entries and payment operation cannot be made for the guest at the master or any other satellites in the IRC system. 32 7. Clerk sign-on report A clerk sign-on report can be generated at the master. This report is used to know at which satellite each clerk has signed on. Report generation procedure 1. 2. Select "PGM2 MODE" from the mode selection window and press the ENTER key. Select "INLINE READING" from the PGM2 MODE window and press the ENTER key. 3. Select "SIGN ON CLERK" from the INLINE READING window and press the ENTER key. 4. Select "DISPLAY" or "REPORT PRINTER" and press the ENTER key. Sample Print (master) P GM 2 S I GN ON NAME CODE M­No. CLERK001 0001 00012 3 CLERK002 0002 000234 CLERK003 0003 000001 Clerk name, clerk code, machine no. of the machine at which the clerk has signed on 33 8. Look-up and updating of the GLU/PBLU file In the IRC system, the GLU/PBLU file exists only in the master. All satellites in the IRC system can access the GLU/PBLU file in the master for registration. GLU/PBLU-file-related inline communications are made for the following purposes: · New order or reorder · Payment entry or temporary finalization · Slip printing · Bill transfer/bill totalizing · Bill separating There are two types of GLU/PBLU data transmission. 1) The GLU/PBLU data is transmitted from the master to a satellite for GLU/PBLU file look-up (in case of a new order/reorder). In this case, the GLU/PBLU reserve counter* is retained at the master. * The reserve counter reserves some records of GLU/PBLU files to prevent a "LACKING MEMORY" error in finalization. 2) The GLU/PBLU data is transmitted from a satellite to the master for finalization of a transaction (in case of payment entry or temporary finalization). The data transmitted from the satellite is once saved in the GLU/PBLU data receiving file and then in the GLU/PBLU file. In this case, the GLU/PBLU reserve counter is cleared at the master. If a satellite looks up the GLU/PBLU file in the master or asks the master to update the file, the backup master performs the same process as the master. 34 9. Drive-through function Depending on the setup of your system. Drive-through data is either centrally controlled by the master or Individually looked up at each terminal. For more information, please contact your authorized Sharp Dealer. Automatic code generation Drive-through codes are generated automatically: when the end code for a transaction is generated, the start code for another transaction is automatically generated. The start/end codes are programmable in the PGM mode. Automatic look-up As drive-through codes are temporarily finalized by pressing the NBAL or FINAL key, data for these codes is automatically looked up in the same sequence as the code was generated. Drive-through-related inline communications are made for the following purposes: · · · · · New order or re-order Payment entry or temporary finalization Slip printing Bill transfer/bill totalizing Bill separating The drive-through data is transmitted from the master to a satellite for drive-through file look-up (in case of a new order/re-order). [. . . ] Install the new ink ribbon cassette so that the ink ribbon gets into the gap shown at left. Ink ribbon 5. Close the ribbon cover. 70 · ER-04RP Physical characteristics Control panel Paper outlet Ribbon cover Online switch Line feed switch Paper cover Connector AC power receptacle Power switch 71 1. Lamps and switches (1) Lamps · Power lamp This lamp lights up when the power switch of the remote printer is turned on. * Online lamp This lamp lights up when the online switch is pressed, and goes off when the switch is pressed again. [. . . ]