User manual SHARP FO-120

[. . . ] This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and the receiver. [. . . ] · Rapid Key Dialing: Press the appropriate Rapid Key. · Speed Dialing: Press the SPEED DIAL key, and enter the 2-digit Speed Dial number with the numeric keys. 01 19 Example: Press Rapid Key 01 6. Making Phone Calls 3 Speak with the other party when they answer. · If you pressed the SPEAKER key, pick up the handset to talk. 79 all-ux510A. book Page 80 Thursday, September 14, 2000 9:05 AM Making Telephone Calls Comments: While the handset of the fax is lifted (off hook), an extension phone connected directly to the fax cannot be used to speak with the other party. The fax may interrupt a voice call received on an extension phone if the reception mode is set to A. M. and there is a period of silence during the conversation. If you are on a touch-tone phone, you can prevent this by pressing any three keys on the phone immediately after you answer. (Note: Do not enter the code to activate fax reception: 5, * , * . ) Searching for an auto-dial number You can use the HOLD/SEARCH key to search for a Rapid Key or Speed Dial number. First search for the number as described in Searching for an auto-dial number on page 63, then pick up the handset or press the SPEAKER key. The number will be dialed automatically (do not press the START key). Redial The last number dialed can be redialed by pressing the REDIAL key (it is not necessary to pick up the handset or press the SPEAKER key). If your answering machine has a toll saver function, make sure that it will answer by the fourth ring. 82 all-ux510A. book Page 83 Thursday, September 14, 2000 9:05 AM Connecting an Answering Machine Note: If your answering machine has a remote retrieval function, make sure the code used to activate remote retrieval is different from the code used to activate fax reception with an extension telephone (see page 71). If they are the same, entering the code from an outside telephone to retrieve messages will cause the fax machine to be activated How the connection operates While you are out, all of your incoming calls will be answered by your answering machine and its outgoing message will play. During this time, your fax will quietly monitor the line. If your fax detects a fax tone or a duration of silence greater than four seconds, it will take over the line and begin reception. Your fax machine listens for a duration of silence because some transmitting machines do not send a fax tone when the fax is sent manually (this means that the person faxing uses the handset to dial and then presses their Start key after listening to your outgoing message). Pressing the Start key in this case causes the line to go silent. When you return and turn off your answering machine, be sure to change the reception mode back to FAX or TEL! 83 7. Answering Machine all-ux510A. book Page 84 Thursday, September 14, 2000 9:05 AM Optional A. M. Mode Settings If necessary, you can use the following settings to improve the response of the answering machine hookup to incoming calls. Quiet Detect Time The fax machine is set to take over the line and begin reception if it detects 4 seconds of silence after the answering machine answers. If needed, you can change this setting to any number of seconds from 1 to 10. We recommend that you do not set Quiet Detect Time under 3 seconds. [. . . ] Studies performed in animal models other than rats did not show any association between carbon black and lung tumors. Signs and Symptoms of Exposure : not applicable Medical Conditions Generally Aggravated by Exposure : not applicable Emergency and First Aid Procedures : not applicable 143 all-ux510A. book Page 144 Thursday, September 14, 2000 9:05 AM SHARP Date Revised: . 22, 1998 MATERIAL SAFETY DATA SHEET (2/2) MSDS No. Physical Chemical Characteristics Boiling/Melting Point Vapor Pressure Vapor Density Evaporation Rate Appearance Odor m. p. [. . . ]