User manual SHARP FO-130/226

[. . . ] AVISO: Para una desconexión eléctrica completa, desenchufar el enchufe del tomacorriente. VARNING: För att helt koppla från strömmen, dra ut stickproppen. ATTENZIONE: Per un totale scollegamento elettrico rimuovere la spina di corrente. "The mains outlet (socket-outlet) shall be installed near the equipment and shall be easily accessible. " "De aansluiting op de stroomvoorziening (stopkontakt) moet nabij het apparaat zijn aangebracht en moet gemakkelijk bereikbaar zijn. " Ett nätuttag (vägguttag) bör befinna sig nära utrustningen och vara lätt att tillgå. [. . . ] When the toner cartridge is empty, the toner cartridge indicator will light steadily and REPLACE TONER will appear in the display. Use the following replacement toner cartridge: Sharp FO-59DC toner cartridge Hint: When the toner cartridge nears empty, try taking it out of the machine and shaking it. This may increase the number of pages that can be printed before the toner runs out. When to replace the drum cartridge When the drum cartridge nears the end of its life, the ALARM indicator on the operation panel will blink and DRUM LIFE REACHED will appear in the display (this message first appears approximately 1000 pages before the drum needs replacement). Use the following replacement drum cartridge: Sharp FO-47DR drum cartridge 45 1. Installation Installing the Print Cartridges Loading Printing Paper Loading Printing Paper You can load up to 250 sheets of A4-size paper (60-80 g/m2) in the paper tray. A paper cassette is available as an option. Up to 500 sheets of A4-sized paper can be loaded in the paper cassette. To have the cassette installed, consult your dealer. Important: Do not use the back side of paper that has already been printed on. Note: If you need to add paper to the tray or cassette while paper still remains, remove the remaining paper and combine it into a single stack with the new paper. Loading paper in the paper tray 1 Remove the received document tray. 2 Insert a stack of paper into the tray, print side up. Red line · Important!The stack of paper must not be higher than the red line on the paper tray. 3 Squeeze the paper guide and move it to match the length of the paper you are loading. Attach an A4 label here to indicate the paper size 46 4 Replace the received document tray. · The received document tray must be attached for the fax machine to operate properly. Loading paper in the paper cassette (if installed) 1 Grasp the hand-hold on the cassette and pull the cassette out until it stops. 2 Push the pressure plate down until it locks into position. 47 1. Installation Loading Printing Paper Loading Printing Paper 3 Squeeze the paper guide and pull up to move it to the appropriate holes for the length of the paper. Push the guide down into the holes. 1 2 4 Place a stack of paper in the cassette, print side up. · Make sure the stack of paper is not higher than the two tabs on the paper guide and the two metal tabs. If it is, remove some of the paper. · If you find it difficult to load the paper, remove the cassette from the machine. Sending Documents Up to 50 A4-sized pages (20 B4-sized pages) can be placed in the feeder at one time. The pages will automatically feed into the machine starting from the bottom page. If you need to send or copy more than 50 pages, place the additional pages gently and carefully in the feeder just before the last page is scanned. Do not try to force them in, as this may cause double-feeding or jamming. If your document consists of several large or thick pages which must be loaded one at a time, insert each page into the feeder as the previous page is being scanned. Insert gently to prevent double-feeding. 1 Adjust the document guides to the width of your document. 2 Place the document face down and push it gently into the document feeder. The top edge of the document should enter the machine first. · The feeder will draw the leading edge of the document into the machine. SEND READY will appear in the display. Note: When inserting a large number of pages in the feeder, slant the front end of the stack so that the bottom pages enter first. 57 Adjusting the Resolution and Contrast 3 Adjust the resolution and/or contrast settings (if desired) and then dial the receiving machine as explained in the following sections. Adjusting the Resolution and Contrast If desired, you can adjust the resolution and contrast before sending a document. Resolution The fax machine has four resolution settings: STANDARD Use STANDARD for ordinary documents. This setting gives you the fastest and most economical transmission. Use FINE for documents containing small letters or fine drawings. Use SUPER FINE for documents containing very small letters or very fine drawings. Use HALF TONE for photographs and illustrations. The original will be reproduced in 64 shades of gray. FINE SUPER FINE HALF TONE The default resolution setting is STANDARD. [. . . ] FUNCTION NO PAPER This message will be followed by one of the paper sources in parentheses, and informs you that the paper source is out of paper. If no paper source is indicated, both paper sources are out of paper. The SPEAKER key has been pressed and the fax machine is waiting for you to dial. The received document tray is not attached. [. . . ]