User manual SHARP FO-3800M

[. . . ] FO-3800M DIGITAL LASER MULTIFUNCTION OPERATION MANUAL COVER PAGE GB 1. p65 1 12/09/00, 09:44 This product contains a lithium-ion battery, and must be disposed of properly. Contact your local environmental officials for disposal instructions. In some areas, the "POWER" switch positions are marked "I" and "0" on the copier instead of "ON" and "OFF". CAUTION: For a complete electrical disconnection, pull out the main plug. The socket-outlet shall be installed near the equipment and shall be easily accessible. Important safety information · If any of your telephone equipment is not operating properly, you should immediately remove it from your telephone line, as it may cause harm to the telephone network. [. . . ] To use Automatic Dialing, you must first store the full number. The way you store it depends on whether you want to use it for Rapid Key Dialing or Speed Dialing: Note: If the machine is connected to a PBX, the numbers dialed in automatic dialing are automatically transferred to the public line (you should not enter access code, etc. ) in order to obtain the external line in case of registred numbers. In case of an internal number of the PBX, push the SPEAKER key in order to insert the R character at the beginning of the number (when you are in step 6, as shown below) ; this will cancel the automatic dialing of the access code. Storing numbers Use the following procedure to store numbers for Rapid Key Dialing or Speed Dialing: 6 Step Press these keys FUNCTION Comments "ENTRY MODE" will appear in the display. "FAX NUMBER MODE" will appear in the display. "FAX NUMBER SET" will appear in the display. To store a Rapid key number, press a Rapid key. To store a Speed Dial number, press two number keys ("00" to "99"). "PRESS ENTER KEY" will appear in the display. "ENTER FAX NUMBER" will appear in the display. 1 2 3 4 DEF 01 (example) 5 6 ABC ENTER JKL ABC WXYZ TUV ABC Enter the fax number (maximum of 20 digits including pauses) using the number keys. (example: 2015298200) 7 8 JKL ENTER "ENTER NAME" will appear in the display. Enter the name of the location or party by pressing number keys as described in "How to Enter Characters " in this chapter (max. If you do not want to enter a name, skip this step. "CHAIN DIAL" will appear in the display. ABC GHI . . . (example) 9 ENTER 58 SUK 06 INITIAL LEO. p65 58 INITIAL SETTINGS 17/04/00, 13:15 Fax Setup 10 ABC or Press "1" if you want to 1 specify the number as a Chain Dialing number (see "Chain Dialing for Long Numbers" in this section). 2 Return to Step 4 to store another number, or press the STOP key a number STOP of times until you exit. If the number is a Rapid key number, you can write the name on the label above the appropriate Rapid key. 11 STOP STOP Step 4 or . . . Note: You may need to add a pause between certain digits in the number to allow time for connection. For example, if you are on a PBX telephone system that requires an access number, such as "9", to be dialed to access an outside line, you will need to enter a pause between the access number and the fax number of the other party. Pauses are entered by pressing the REDIAL/PAUSE key (2 seconds per pause). If REDIAL/PA necessary, several pauses can be entered in a row. Use the following procedure to clear numbers: 6 Step Press these keys FUNCTION DEF Comments "ENTRY MODE" will appear in the display. "FAX NUMBER MODE" will appear in the display. 1 2 3 4 ABC Select CLEAR. "FAX NUMBER CLEAR" will appear in the display. To clear a Rapid key number, press the appropriate Rapid key. To clear a Speed Dial number, enter the 2-digit number with the number keys. "PRESS ENTER KEY" will appear in the display. [. . . ] Eye ; In case of contact, immediately flush eyes with water for 15 minutes. Section 6. Physical Physical Chemical Characteristics : Not applicable : Not applicable : Not applicable : Not applicable : Fine powder : Odorless Gravity Specific Gravity Solubility in Water PH Viscosity Color : 1. 1 : Negligible : Not applicable : Not applicable : Black Point Boiling/Melting Point Vapor Pressure Vapor Density Evaporation Evaporation Rate Appearance Odor Section 7. Fire and Explosion Data : Not applicable : No data available : (LEL); Not applicable (UEL); Not applicable Extinguishing Media : CO2, dry chemical, foam or water Special Fire Fighting Procedure : None Unusual Fire and Explosion Hazard : This material has no unusual fire or explosion hazards. Sensitivity to Mechanical Impact : None Sensitivity to Static Charge : None Point Flash Point (Method Used) Ignition Temperature Flammable Flammable Limits 138 SUK SAFETY DATA SHEET LEO. p65 MATERIAL SAFETY DATA SHEET 138 19/06/00, 11:53 License Agreements Section 8. Stability Av Incompatibility (Material to Avoid) Hazardous Decomposition Hazardous Pol olymerization Hazardous Polymerization Reactivity Data : Stable : None : CO : Will not occur. Section 9. for Safe Precautions for Safe Handling and Use ersonal Protection Information (Respiratory Eye Protection Protective Glove): Personal Protection Information (Respiratory, Eye Protection and Protective Glove): Use of a dust mask is recommended when handling a large quantity of toner or during long term exposure, as with any non-toxic dust. Control/V ol/Ventilation Engineering Control/Ventilation : Not required. Work/Hygienic Practice : Inhalation should be minimized as with any non-toxic dust. [. . . ]