User manual SHARP FO-IS125N BROCHURE

[. . . ] Este equipamento obedece s exigncias da directiva 1999/5/CE. Denna utrustning uppfyller kraven enligt direktiv 1999/5/EC. Dette produktet oppfyller kravene i direktiv 1999/5/EC. Dette udstyr overholder kravene i direktiv 1999/5/EF. [. . . ] If you wish to enter more destinations, go to Step 8. If you have finished entering destinations or are only entering one destination, go to Step 9. 8 Repeat Steps 6 and 7 for each of the destinations that you wish to enter. (A maximum of 50 destinations can be entered. ) You can press to scroll through and check your entered destinations. DEL To delete a destination, press when it appears. 9 Press START . The document will be scanned into memory and the timer number assigned to the job will appear briefly in the display. Transmission will take place at the specified time. 101 7. Special Functions If [MEMORY FULL] appears, see If the memory becomes full on page 81. Timer Transmission Checking and cancelling stored timer transmission jobs Follow the steps below to check the timer transmission jobs that are stored. If needed, you can also use this procedure to cancel a stored job. 1 2 3 Press TIMER . Press to select "REVIEW". Press or to scroll through the stored timer transmission jobs. For each job, the timer number, the destination, and the specified time appear. 4 To cancel a displayed job, press complete the cancelation (press START . Press START once again to STOP if you do not wish to cancel ). 5 When finished, press STOP to exit. 102 The option settings allow you to customize the operation of the machine to better suit your needs. The option settings have been initially configured at the factory. To change a setting, follow the steps below to display the setting, and then enter a new selection for the setting as explained in the table that follows. 1 2 Press FUNCTION , then until [OPTION SETTING] appears. Press , then repeatedly until the desired setting appears. The option settings are described in the table below and on the following pages. 3 4 Enter a selection for the setting by pressing the number keys as explained in the table. After entering a selection, the subsequent option setting will appear in the display. To exit the settings, press STOP . Option Settings Make a selection for the displayed setting as explained below. (The report can still be printed manually at any time. ) Press to turn off Auto Print Out. Initial setting: NO ECM MODE (NO) Press (YES) to have any distortions in a transmission due to noise on the telephone line automatically corrected before printout at the receiving end. This is only effective when the other machine has ECM as well. (When there is considerable noise on the line, you may find that ECM slows transmission. Turning off ECM mode may increase transmission speed. ) Initial setting: YES LANGUAGE SELECTION This sets the language that appears in the display, reports, and lists. Press for English, for Swedish or for Polish. A beep will sound and the display will change to the selected language. Initial setting: ENGLISH 105 Option Settings PBX CONNECTION If you are on a PBX, use this setting to set up automatic connection to an outside line when dialing by automatic dialing. (When this is done, unless you press the key before dialing to dial manually, you will always automatically connect to an outside line when you dial on the machine; there will be no need to press the flash key ( R SPEAKER ) or dial a prefix in order to dial out. ) 1. Press (YES) to enable the PBX connection setting. ( (NO) should be selected if you are not on a PBX. ) 2. [. . . ] n alte ri din afara Uniunii Europene Dac dorii s aruncai acest produs, v rugm contactai autoritatea local pentru a afla care este metoda corect de eliminare. B. Informaii pentru utilizatorii profesionali 1. n Uniunea European Dac produsul este de uz profesional i dorii s l aruncai: V rugm contactai distribuitorul SHARP care v va furniza informaii privind preluarea produsului. Este posibil s vi se cear s acoperii cheltuielile ocazionate de preluare i reciclare. [. . . ]