User manual SHARP FU-40SE-P

[. . . ] R FU-40SE-P AIR PURIFIER OPERATION MANUAL Tabletop / wall-mounting type ENGLISH FEATURES Cluster Ion Control The unit controls the ratio of minus cluster ions and plus cluster ions depending on the condition of the room. CONTENTS SAFETY PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . E-2 · CAUTIONS CONCERNING THE USAGE OF THIS PRODUCT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E-3 · CAUTIONS WHEN MOUNTING THIS PRODUCT TO A WALL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E-3 · CAUTIONS CONCERNING THE INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] · When mounting the unit to a wall, remove the front panel and hold the main unit. Holding the front panel may cause it to become detached, thus dropping the unit and resulting in bodily injury. · Do not install when there is generation of lampblack, such as in a kitchen, etc. The unit surface may crack or the sensors may malfunction as a result. CAUTIONS CONCERNING THE INSTALLATION DO NOT USE THE REMOTE CONTROL IN THE FOLLOWING LOCATIONS · Location where there are inverter lighting equipment or electronic spontaneous lighting equipment The remote control may become inoperative. In this case, move away from such lighting equipment or change direction. · Location exposed to direct sunlight The unit may not received signals from the remote control The unit may not respond to the signals of the remote control if the ends of fluorescent lighting become black or lights flicker due the depletion of service life; however, this is not a malfunction of the remote control or the main unit. In this case, replace the lighting with new fluorescent tubes. TAKE CAUTION TO THE FOLLOWING DURING INSTALLATION · Leave at least 2m of space from televisions, radios and wave clocks. Electrical interference may occur as a result. · Leave at least 60cm of space from the wall The motor may overheat, causing malfunction as a result. · Avoid a location where sensors are exposed to direct wind The unit may not operate properly. · Avoid a location where curtains, etc. , come into contact with the intake or exhaust port. Curtains, etc. , may become dirty or malfunction may occur as a result. EFFECTIVE USAGE · Stable surface with sufficient air circulation · Near smoking area Air pollution is detected quickly. ABOUT THE FILTER · Do not wash and reuse Apatite HEPA filter and deodorization filter. It does not effect, and may become a cause of electric shock and trouble. · Small dust and odors such as tobacco smoke rise and accumulate at the top of the room. · Large dust such as pollen and house dust accumulate at the bottom of the room. · The wall, etc. , behind the exhaust port may become dirty as time passes. When using the unit for extensive period in the same location, use a vinyl sheet, etc. , to prevent the wall from becoming dirty. In addition, periodical clean the wall, etc. E-3 NAMES OF PARTS MAIN UNIT DISPLAY substances *It can't remove the noxiouscigarette. (carbon monoxide etc. ) of Power lamp (Lights when the power plug is inserted into the wall outlet) Tobacco smoke mode operation lamp Filter timer lamp AUTO operation lamp Pollen mode operation lamp * Fan level lamps OFF timer display lamps (set using remote control) Plasmacluster High Silent Median Max Remote control receiver Dust sensor Odor sensor (Detects odors such as tobacco smoke, incense, pets, cosmetics, etc. ) (Detects dust, smoke, pollen, house dust, etc. ) Clean-sign lamp The color changes when the air is dirty Clean (green) Little dirty (orange) Very dirty (red) ABOUT THE CLEAN-SIGN LAMP · The dust sensor displays a clean sign depending on the relative change of the environment at the time the power plug is inserted in the wall outlet and after. · When the air is extremely dirty at the time the power plug is inserted, the clean sign lamp may light green since the polluted state is the environment which the sensor bases the pollution rate on. · In this case, switch manually to desirable operation as effective operation can't be done in auto operation. · To reset the base pollution rate of the clean-sign lamp remove and insert the power plug again the room air becomes clean. EXPLODED DIAGRAM MODE-ON/OFF button (Used to select operations or turn the unit off) Main unit HEPA filter (white) (Dust collection filter) (W/ apatite antibacterial filter) Stamina-power carbon (black) (Deodorization filter) Pre-filter Front panel Remote control Hook Stand (Be sure to mount for tabletop installation) Thumbscrew E-4 CLUSTER ION LAMP Cluster ion operation is selected using the remote control. Blue light When the cluster ion operation is in the Clean mode or AUTO cluster ion mode and the air in the room is dirty, the light turns on and the unit will operate in the Clean mode. Green light When the cluster ion operation is in the Refresh mode or AUTO cluster ion mode and the air in the room is clean, the light turns on and the unit will operate in the Refresh mode. Light off No cluster ions are generated. [. . . ] If the filter replacement lamp is on, the lamp will turn off. Fill in the usage start date of the filters on the date label included with the replacement filters. Affix the label on top of the replacement label that is already on the back of the front panel. Replacement filters · HEPA filter: 1 unit · Stamina-power carbon: 1 unit Model: FZ-40SEF Please ask for replacement filters at your dealer of purchase. Cautions concerning the disposal of filters Please dispose of replaced filters according to the local disposal laws and regulations. HEPA filter materials: · Filter: Polypropylene · Frame: Polyester Stamina-power carbon materials: · Deodorizer: Activated charcoal · Frame: Polyester E-13 TROUBLESHOOTING Before calling for repair, check the symptoms below for possible remedies, since the problem may not be a malfunction of the unit. SYMPTOM The remote control does not work Odours and smoke cannot be removed easily The Clean sign lights green even when the air is dirty The Clean sign lights orange or red even when the air is clean The cluster ion lamp remains green (blue) and does not change A sound is heard from the unit Click, click Tick, tick, tick REMEDY (not a malfunction) · Have the batteries been depleted?· Are the batteries inserted correctly? [. . . ]