User manual SHARP FU-60SE-P

[. . . ] R FU-60SE-P Floor / Tabletop type *Plasmacluster is a trademark of Sharp Corporation. ENGLISH AIR PURIFIER OPERATION MANUAL ENGLISH FEATURES Plasmacluster Ion Control The unit controls the ratio of negative ions and positive ions depending on the condition of the room. · Clean Mode Approximately the same numbers of positive and negative ions are discharged. This mode is effective for reducing some airborne mold. CONTENTS SAFETY PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . E-2 · RISK OF ELECTRIC SHOCK . . . . . . . . . . . . . . . . . . . . . . E-2 · CAUTIONS CONCERNING THE OPERATION OF THIS PRODUCT . . . . . . . . . . . . . . [. . . ] · When transporting the unit, always hold the handle on the back of the unit. Holding the front panel when carrying may cause it to detach, thus dropping the unit and resulting in bodily injury. REMOTE CONTROL LIMITATIONS DO NOT USE THE REMOTE CONTROL IN THE FOLLOWING LOCATIONS · Any location where there is inverter lighting equipment or electronic spontaneous lighting equipment The remote control may become inoperative. In this case, move away from such lighting equipment or change direction. · Location exposed to direct sunlight The unit may not receive signals from the remote control. The unit may not respond to the signals of the remote control if the ends of fluorescent lighting become black or lights flicker due to the depletion of service life; however, this is not a malfunction of the remote control or the main unit. In this case, replace the lighting with new fluorescent tubes. INSTALLATION GUIDELINES · Leave at least 2m of space from equipments which involve electric wave such as televisions, radios or wave clocks. Electrical interference may occur if not. · Leave at least 60cm of space from the wall The motor may overheat, causing malfunction if not. · Avoid a location where sensors are exposed to direct wind The unit may not operate properly. · Avoid a location where curtains, etc. , come into contact with the intake or air outlet. Curtains, etc. , may become dirty or malfunction may occur as a result. EFFECTIVE OPERATION · Place on a stable surface with sufficient air circulation FILTER GUIDELINES · Do not wash and reuse HEPA Filter and Active Carbon Filter. It does not work effectively, and may become a cause of electric shock. · The wall behind the air outlet may become dirty as time passes. When using the unit for extensive period in the same location, use a vinyl sheet, etc. , to prevent the wall from becoming dirty. In addition, periodically clean the wall, etc. E-3 ENGLISH PART NAMES MAIN UNIT DISPLAY OFF Timer Display Indicator Lights (set using remote control) AUTO Operation Indicator Light Fan Level Indicator Light Filter Indicator Light If the Filter Indicator Light is lit, it indicates filter replacement period. PLASMACLUSTER INDICATOR LIGHT Plasmacluster ion operation is selected using the remote control. Blue light When the Plasmacluster ion operation is in Clean Mode, or in AUTO Plasmacluster Ion Mode and the air in the room is impure, the light will activate and the unit will operate in Clean Mode. Green light When the Plasmacluster ion operation is in the Ion Control Mode, or in AUTO Plasmacluster Ion Mode and the air in the room is clean, this light will activate and the unit will operate in Ion Control Mode. Light off There are no Plasmacluster ions being generated. · The light can be turned off by using the `Display ON/OFF Button' on the Remote Control even while Plasmacluster ions are generated. (Please turn off the light when not required. ) E-4 Pollen Mode Indicator Light CLEAN-SIGN LIGHT The color changes according to the air condition. Clean (Green) Slightly Impure (Orange) Very Impure (Red) CLEAN-SIGN CLEAN-SIGN CLEAN-SIGN ABOUT THE CLEAN-SIGN · The sensors display a CLEAN-SIGN depending on relative changes to the environment from the time the power plug is inserted into the wall outlet and thereafter. · When the air is extremely impure at the time the power plug is inserted, the CLEAN-SIGN LIGHT may light green since the impure condition is the environment against which the sensors base the impurity rate on. In this case, operate the unit for a while in Clean Mode first, then switch to the desired operation mode. See Page E-11 · To reset the base impurity rate on the CLEAN-SIGN remove and insert the power plug. · The CLEAN-SIGN LIGHT can be turned off using the "Display ON/ OFF" Button of the Remote Control. [. . . ] · Is a fluorescent lighting in the room flickering due to service life?(Refer to E-3, E-7) · Are the filters heavily soiled?(Refer to E-13) · Is the opening of the odor sensor blocked or the sensor filter clogged?(Refer to E-12) · The air could be impure at the time the unit was plugged in. [. . . ]