User manual SHARP FZ-6400SF annexe 1

[. . . ] 22 Controlling the Projector via LAN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 Controlling the Projector Using Internet Explorer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 Controlling the Projector and Confirming the Projector Status . . . . . . . . . . . . . . . . 25 Making General Settings for the Network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 Operating the Projector Using the PJLinkTM Protocol . . . . . . . . . . . . . . . . . . . 27 Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 Setting up the Screen For optimal image quality, position the projector perpendicular to the screen with the projector's feet flat and level. [. . . ] ?1 T A B N _ _ _ 1 0: Normal 8: Lamp Life 5% or less 16: Lamp Burn-out 32: Lamp Ignition Failure Lamp Lamp1 Status Lamp2 Status Power Status Quantity Lamp1 Usage Time(Hour) Lamp2 Usage Time(Hour) Lamp1 Usage Time(Minute) Lamp2 Usage Time(Minute) Lamp1 Life(Percentage) Lamp2 Life(Percentage) Lamp1 Timer Reset *1 Lamp2 Timer Reset *1 TLPS_ TLPS_ T POW_ TLPN_ TLTT_ TLTT _ TLTM_ TLTM_ TLTL_ TLTL _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 1 0: Off, 1: On, 2: Retry 3: Waiting, 4: Lamp Error 2 0: Off, 1: On, 2: Retry 3: Waiting, 4: Lamp Error 1 1: On, 2: Cooling 12 1 0 ­ 9999(Integer) 2 0 ­ 9999(Integer) 1 0, 15, 30, 45 2 0, 15, 30, 45 1 0% ­ 100%(Integer) 2 0% ­ 100%(Integer) L P R E 0 0 0 1 ERR OK or ERR Name Model Name Check Model Name Check Serial No. Check *2 Projector Name Setting 1 (First 4 characters) *3 Projector Name Setting 2 (Middle 4 characters) *3 Projector Name Setting 3 (Last 4 characters) *3 Projector Name Check L P R E 0 0 0 2 ERR OK or ERR T N A M _ _ _ 1 XGPH80WN/XGPH80XN M N R D _ _ _ 1 XG-PH80W-N/FZ-6400SF S N R D _ _ _ 1 Serial No. PJN1 PJN2 PJN3 PJN0 I I I I I I I * * * _ * * * _ _ _ _ _ _ _ * * * _ _ _ _ _ _ _ * OK or ERR * OK or ERR * OK or ERR 1 Projector Name 1 OK or ERR 2 OK or ERR 3 OK or ERR 4 OK or ERR 1 OK or ERR 2 OK or ERR ERR ERR ERR ERR ERR ERR ERR Input Change COMPUTER1 COMPUTER2 (5BNC) COMPUTER3 (DVI) COMPONENT S-VIDEO VIDEO Input RGB Check RGB_ RGB_ RGB_ RGB_ VED_ VED_ R G B ?1: COMPUTER1, 2: COMPUTER2, 3: DVI, 4: COMPONENT or ERR Input Video Check Input Mode Check I V E D ?1: S-VIDEO, 2: VIDEO or ERR ERR ERR I M O D ?1: RGB, 2: VIDEO *1 The Lamp Timer Reset command is available only in standby mode. Check command is used to read out the 12 digits of serial No. *3 For setting the projector name, send the commands in the order of PJN1, PJN2 and PJN3. -17 Setting up the Projector Network Environment This section describes the basic procedure for using the projector via the network. If the network is already constructed, the projector's network settings may need to be changed. Please consult your network administrator for assistance with these settings. You can make network settings both on the projector and on the computer. The "System Configuration" screen appears, ready for network settings for the projector. Items IP Address Setting example / Remarks You can set this item when "DHCP Client" is set to "OFF". Factory default setting: 192. 168. 150. 2 Enter an IP address appropriate for the network. You can set this item when "DHCP Client" is set to "OFF". Factory default setting: 255. 255. 255. 0 Set the subnet mask to the same as that of the computer and equipment on the network. You can set this item when "DHCP Client" is set to "OFF". Factory default setting: 0. 0. 0. 0 * When not in use, set to "0. 0. 0. 0". Factory default setting: 0. 0. 0. 0 * When not in use, set to "0. 0. 0. 0". Select "ON" or "OFF" to determine whether to use DHCP Client. 2 Subnet Mask Default Gateway Note · Confirm the existing network's segment (IP address group) to avoid setting an IP address that duplicates the IP addresses of other network equipment or computers. If "192. 168. 150. 2" is not used in the network having an IP address of "192. 168. 150. XXX", you don't have to change the projector IP address. · For details about each setting, consult your network administrator. DNS Server DHCP Client -22 Setting up the Projector Network Environment 3 Confirm that the values are set properly, and then click the "Apply" button. · Close the browser. · This completes the network settings. [. . . ] Check that the LAN cable is a straight-through cable when connecting the projector with a network device such as a hub. Check that the power supply is turned on for the network device such as a hub between the projector and a computer. Check the network settings for the computer and the projector Check the following network settings for the projector. · IP Address Check that the IP address for the projector is not duplicated on the network. · Subnet Mask When the gateway setting for the projector is "0. 0. 0. 0" (Not Used), or the gateway setting for the projector and the default gateway setting for the computer are the same: · The subnet masks for the projector and the computer should be the same. [. . . ]