User manual SHARP FZ-6500SF annexe 1

[. . . ] Connecting the Projector to a Computer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Setting an IP Address for the Computer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Setting up a Network Connection for the Projector . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Controlling the Projector via LAN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] · The power switches of both the projector and the computer are on. This completes the connection. Setting an IP Address for the Computer". -12 Setting up the Projector Network Environment 2. Setting an IP Address for the Computer The following describes how to make settings in Windows Vista®. 1 2 Log on the network using the administrator's account for the computer. Click "start", and click "Control Panel". 2 1 3 Click "View network status and tasks" of "Network and Internet", and click "View status" in the new window. · This manual uses examples to explain the operations in Category View. If you are using Classic View, double-click "Network and Sharing Center". 1 XXXXXXXXX 2 4 Click "Properties". · When the user account control display is displayed, click "Continue". 1 -13 Setting up the Projector Network Environment 5 Click "Internet Protocol Version 4 (TCP/IPv4)", and click the "Properties" button. 1 2 6 Confirm or change an IP address for the setup computer. 1 Confirm and note the current IP address, Subnet mask and Default gateway. Make sure to note the current IP address, Subnet mask and Default gateway as you will be required to reset them later. 2 Set temporarily as follows: IP address: 192. 168. 150. 3 Subnet mask: 255. 255. 255. 0 Default gateway: (Do not input any values. ) Note · The factory default settings for the projector are as follows: DHCP Client: OFF IP address: 192. 168. 150. 2 Subnet mask: 255. 255. 255. 0 Default gateway: 0. 0. 0. 0 7 After setting, click the "OK" button, and then restart the computer. After confirming or setting, proceed to "3. Setting up Network Connection for the Projector". -14 Setting up the Projector Network Environment 3. Setting up a Network Connection for the Projector Settings for such items as the projector's IP address and subnet mask are compatible with the existing network. Set each item on the projector as follows. If you did not change the IP address in "3. Setting up a Network Connection for the Projector" (pages 15-16), enter "http://192. 168. 150. 2/". 3 A screen for controlling the projector appears, ready for performing various status conditions, control, and settings. -17 Controlling the Projector via LAN Confirming the Projector Status (Status) Controlling the Projector (Control) 2 30 1 On this screen, you can perform projector control. You can control the following items: On this screen, you can confirm the projector status. You can confirm the following items: · MAC Address · Power · Condition · Lamp Timer · Lamp Life · Input · Signal Info · Serial Number Note · If you click the "Refresh" button before the screen is displayed completely, an error message ("Server Busy Error") will be displayed. Wait for a moment and then operate again. · For details about each item, refer to the projector's operation manual. · Power · Input Select · Audio Input · Volume · AV Mute Note · If you click the "Refresh" button before the screen is displayed completely, an error message ("Server Busy Error") will be displayed. Wait for a moment and then operate again. · You cannot operate this page while the projector is warming up. · While the projector is in standby mode, you can only control "Power ON". · For details about each item, refer to the projector's operation manual. -18 Controlling the Projector via LAN Setting and Adjusting the Projector (Settings & Adjustments) Example: "Picture" screen display for COMPUTER1 Setting the Security (Network ­ Security) On these screens, you can make projector settings or adjustments. You can set or adjust the following items: · · · · · · · · · · · · · · · Picture Mode CLR Temp BrilliantColorTM DNR Eco + Quiet Resolution Setting Signal Type Dynamic Range Video System Video Setup Resize Overscan OSD Display Background Memory Load · · · · · · · · · · · · · · · Projection Mode Wall Color OSD Language Auto Sync Auto Power Off Auto Restart Internal Speaker Audio Out RS-232C Speed Fan Mode COMPUTER2 Select DLP® LinkTM DLP® LinkTM Invert Rotate Indicator All Reset On this screen, you can make settings relating to security. Items User Name Password Accept IP Address All IP Addresses From only specific IP addresses Description Setting of user name for security protection. [. . . ] · The IP address parts shown by the subnet mask for the projector and the computer should be the same. (Example) When the IP address is "192. 168. 150. 2" and the subnet mask is "255. 255. 255. 0" for the projector, the IP address for the computer should be "192. 168. 150. X" (X=3-254) and the subnet mask should be "255. 255. 255. 0". · Gateway When the gateway setting for the projector is "0. 0. 0. 0" (Not Used), or the gateway setting for the projector and the default gateway setting for the computer are the same: · The subnets for the projector and the computer should be the same. · The IP address parts shown by the subnet mask for the projector and the computer should be the same. [. . . ]