User manual SHARP HT-CN500DVW

[. . . ] This product contains a low power laser device. To ensure continued safety, do not remove any cover to attempt to gain access to the inside of the product. Refer all servicing to qualified personnel. Important Instruction - Introduction / Special notes - When the ON/STAND-BY button is set at STAND-BY position, mains voltage is still present inside the unit. When the ON/STAND-BY button is set at STAND-BY position, the unit may be brought into operation by the remote control. [. . . ] The search does not operate on JPEG discs. MIC LISTENING ECHO MODE VOLUME You can move to other tracks with simple operations. When playing SVCD or VCD, cancel the P. B. C. (playback control) (see page 37). To locate the beginning of a chapter (track) (skip) or button. Whilst a disc is playing, press the Use the button to skip to the next chapter (track). Use the button to skip to the previous chapter (track). On SVCD, VCD and Audio CD, press the button to skip to the beginning of the current track. Press the button again (twice) to skip to the beginning of the previous track. You can playback the desired tracks with titles or chapters in a specific order. Maximum of 20 tracks can be programmed. To play in the desired order (programmed play) 1 Whilst in the stop or playback mode, press the PROG button. TV screen Program : Track (01-23) 01 02 03 04 05 Reset TT: TT: TT: TT: TT: CH: CH: CH: CH: CH: Exit 06 07 08 09 10 TT: TT: TT: TT: TT: CH: CH: CH: CH: CH: Next Notes: Some discs do not display the chapter (track) and the skip feature is disabled. On a DVD, skip does not operate between titles. Alternatively, press the or button on the main unit. Continued to the next page DVD Operation 2 Press the PLAY/PAUSE playback. button to return to the normal E-28 - Basic operation - HT-CN500DVW Basic operation (continued) 2 Enter title or chapter number with the Direct Number buttons. To specify title or track 1, enter "01" (must use 2 digits). If you enter the wrong numbers, press or button to select the concerned track and then reenter the new numbers. To clear all the numbers those entered, press to select "Reset" and then press ENTER button. " TRACK" "REP 1" 2 To play repeatedly (repeat play) You can play a chapter (track) or a title repeatedly by specifying it during playback. When playing SVCD or VCD, cancel the P. B. C. (playback control) (see page 37). To return to the normal playback, press the REPEAT button repeatedly until no display on TV screen. button. Otherwise, the disc Caution: After performing repeat play, be sure to press the STOP will play continuously. Note: On some discs, the repeat play function is disabled. E-32 - Useful operation - 1 2 3 The normal playback. "REPEAT OFF" No display The repeat play mode changes as follows on SVCD/VCD: DVD Operation Repeat the currently playing disc. HT-CN500DVW Useful operation (continued) To play the contents between the specified points repeatedly (A-B repeat) You can play the desired portion repeatedly by specifying it during playback. ENGLISH To select a title from the top menu of the disc On a DVD with multiple titles, you can select a title from the top menu. 1 Whilst a disc is playing, press the A - B button. TV screen Unit display 1 2 Whilst in the stop or playback mode, press the TITLE/RETURN button to display the title menu. or Example 1 Drama 3 SF 2 Action 4 Comedy A A- button to select a title, and then press the This registers the start point (A). 2 Press the A - B button again to enter the end point (B). AB A-B The selected title plays. Or use the Direct Number buttons for some discs. DVD Operation Note: - Useful operation - The procedure shown here provides only general steps. The actual procedure for using the title menu depends on the disc. See the disc jacket for details. This starts A-B repeat from the start point (A) to the end point (B). 3 Press the A - B button to return to the normal playback. Notes: A-B repeat play is disabled on some discs. A-B repeat play for DVD is possible only within a title. A-B repeat play for SVCD/VCD is possible only within a track. [. . . ] If the unit is not restored in the previous operation, unplug and plug in the unit, and then turn the power on. The preset channel cannot be recalled. P. 43 When the protection circuit is activated: When short-circuiting the speaker leads or turning the volume too high, the protection circuit may be activated and the system may enter the stand-by mode. Unplug the unit and, after 15 minutes or more, plug it in again. Turn down the volume if set too high. - Troubleshooting chart - Remote control Symptom The remote control does not operate properly. [. . . ]