User manual SHARP IG-A40U

[. . . ] IG-A40U Please read this manual carefully and retain for future reference. E-15 • To enable stable emission of high-density Plasmacluster ions, the Plasmacluster Ion Generating Unit mounted in IG-A40U will need to be replaced periodically*. * Replacement is required approximately every 2 years (17, 500 hours) when operated 24 hours a day. IGA40U will stop operating after about 26 months (19, 000 hours) if the Plasmacluster Ion Generating Unit is not replaced. [. . . ] € DO NOT use it in the areas, where the unit may get wet. € DO NOT use spray products near the unit. € DO NOT use in the rooms, containing oil component, incense, cigarettes’ sparks, and chemical fumes. € DO NOT operate when using aerosol insecticides or in rooms where there is oily residue, incense, sparks from lit cigarettes, chemical fumes in the air, or in locations where the unit may get wet, such as a bathroom. € DO NOT use these silicone-containing products in the room where the unit is installed. € Only a Sharp Authorized Service Center should service this Plasmacluster Ion Generator. Contact the nearest Service Center for any problems, adjustments, or repairs. € This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. € Children should be supervised to ensure that they do not play with the appliance. € Do not ride the main unit and do not sit on or lean on it, it may cause the injury or damage to the unit. cAUTIONS CONCERNING OPERATION: • DO NOT block the air intake and/or air outlet. € DO NOT use the unit near or on hot objects, such as stoves or heaters or where it may come into contact with steam. Light (blue) LOW Light (blue) OPERATION Button UNIT RESET Button Use this button when replacing Plasmacluster Ion Generating Unit. Don't press it for any other purposes. FILTER RESET Button After cleaning the filter, plug the power cord and press the FILTER RESET button for 3 seconds. AUTO RESTART Switch FIX THE OPERATION COVER BY SCREW If necessary, operation cover can be fixed by accessory screw. Indd 9 2009/05/29 11:40:58 ESPAÑOL FRANÇAIS DISPLAY ENGLISH INSTALLATION POSITION Place the main unit on a smooth, stable surface in a room, and insert the plug into an outlet. TOP min 24 in (60cm) BACKSIDE min 2 1/2 in (6cm) SIDE min 24 in (60cm) SIDE min 24 in (60cm) Installation Guidance • To ensure proper performance, do not put anything in front of the unit. € To ensure proper performance, do not block the air intake or push in anything into the unit. Do not use these silicone-containing products in the room where the unit is installed. SPRAY WAX PESTICIDES * Hair care products, cosmetic products, water proof sprays, polish glass cleaner, wipe and wax. € Operation manual • Screw kit ACCESSORIES Screw kit for operation cover screw (1pc) rubber cover (1pc) washer (1pc) E-8 A40U. [. . . ] SPECIFICATIONS Model Power supply Fan Speed Adjustment Power consumption (W) Operating noise level (dBA) Airflow volume CFM (m3/min) Applicable floor surface area *1 Ion density (ions/cm3) *2 Power cord Outer dimensions Weight IG-A40U HIGH 37 47 494(14) 25, 000 120V 60Hz MED. 5) 7, 000 *1 The target floor surface area for which an emitted airborne ion density of about 25, 000 ions/cm3 can be measured at a point near the center of the room (at a height of about 1. 2m from the floor), during operation at the HIGH mode when the main unit is placed near a wall. *2 Ion count per cm3 blown into air at around the center of the room ( at a height of approx. [. . . ]