User manual SHARP IM-DR420H

[. . . ] PORTABLER 1-BIT-MD-RECORDER ENREGISTREUR MINIDISC PORTABLE 1-BIT 1-BIT BÄRBAR MINISKIVINSPELARE REGISTRATORE DI MINIDISCHI PORTATILE A 1-BIT 1-BIT DRAAGBARE MINIDISC RECORDER 1-BIT PORTABLE MINIDISC RECORDER MODELL MODELLO MODÈLE MODEL MODELL MODEL DEUTSCH Siehe Seiten i bis vi und D-1 bis D-54. FRANÇAIS Se reporter aux pages i à vi et F-1 à F-54. SVENSKA Hänvisa till sidorna i till vi och V-1 till V-54. ITALIANO Leggere le pagine i a vi e I-1 a I-54. [. . . ] When recording is paused or whilst recording. . . 1 2 3 4 5 Press the MENU/ENTER button. Press the or button repeatedly to select or button to select "MARK OFF". Press the MENU/ENTER button. Notes: " Complete the operation within 7 seconds whilst selecting the menus. " When making digital recordings using a CD player or an MiniDisc player, track numbers will be created automatically regardless of the setting of the auto marker function. E-24 IM-DR420H TINSZ0964AWZZ 03/7/21 IM-DR420H_SEEG_E. fm -Advanced Recording- Press the MENU/ENTER button. Useful Features IM-DR420H Advanced Recording (continued) !Track numbers are created automatically during recording via the analogue connection when a silence of 1 second or more is detected (auto marker function). A series of tracks can be recorded as one by disabling the auto marker function (see page 24). " When recording, if a programmed playback is performed by the source or playback is performed by selecting tracks manually, the MiniDisc track numbers may not be the same as on the source. " Track numbers may not be created properly, depending on the connected stereo system. ENGLISH Useful Features -Advanced Recording- About 1 second Silence First track Second track !About sampling rate converter This portable MD incorporates a sampling rate converter so that it can record from digital radios or DAT tape recorders. !When recording from a CD or a MiniDisc using the digital connection, track numbers will be created at the same points as on the CD or MiniDisc (synchro marker function). You cannot copy a MiniDisc that you recorded from digital inputs to another MiniDisc or DAT. It is prevented by the SCMS (Serial Copy Management System). Recording from analogue inputs is not affected. Digital signals Digitally recorded MiniDisc Cannot record Playback side Recording side First track Track A First track Track A Second track Third track Track B Track C Second track Third track Track C Track B CD player, MiniDisc player, etc. Digital connection Digital connection " Track numbers may not be created in proper places, depending on the source to be recorded from, such as signals with noise. " The track numbers on the playback side may not match the track numbers recorded on the MiniDisc. E-25 IM-DR420H TINSZ0964AWZZ 03/7/21 IM-DR420H_SEEG_E. fm Recording from a Microphone 5 6 7 Press the Level". or button repeatedly to select "Mic IM-DR420H ENGLISH Press the MENU/ENTER button. Press the or button repeatedly to select "Auto-Hi", "Auto-Lo" or "MANUAL". Stereo microphone (commercially available) ( To the MIC IN PLUG IN POWER socket ) " The automatic level adjustment may be delayed by a few seconds where source sounds show sudden and rapid changes (especially in meetings and conversations). In this case adjust the recording level manually (see page 27). 8 Press the MENU/ENTER button. The mode will be set automatically after 7 seconds even if the MENU/ENTER button is not pressed. 1 2 3 4 Connect a stereo microphone to the MIC IN socket. Press the MENU/ENTER button. 9 Select the recording mode (steps 1 - 5, page 21). 10Press the button. Recording will start. IM-DR420H TINSZ0964AWZZ 03/7/21 IM-DR420H_SEEG_E. fm Useful Features " When "Auto-Hi" or "Auto-Lo" is selected, the recording level is automatically adjusted according to changes in sound volume. When the recording level frequently reaches "OVER", switch to "Auto-Lo" to lower the level. Set the maximum level between "-4 dB" and "0 dB". E-26 -Recording from a Microphone- IM-DR420H Recording from a Microphone (continued) !Adjusting the microphone recording level (Manual) To interrupt recording Press the button whilst recording. [. . . ] Cleaning When the unit becomes dirty Clean it with a soft cloth. When the unit is excessively dirty, use a soft cloth dampened in water (external surfaces only). Clean the plugs and the connecting sockets. If the plugs or sockets are dirty, noise may be heard. [. . . ]