User manual SHARP LC

[. . . ] The numbers are located in the rear of the product. Model No. : Serial No. : U. S. A. ONLY IMPORTANT INFORMATION WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within a triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product. CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. 1 US IMPORTANT INFORMATION (Continued) WARNING: FCC Regulations state that any unauthorized changes or modifications to this equipment not expressly approved by the manufacturer could void the user's authority to operate this equipment. [. . . ] Setting Enlarge Panel Protection Cover 54 Lock Item Menu Display/Remote/Buttons/Power/ RS-232C PIN/PIN Clear 54 54 Start Now/When Connected 55 H-Pos. /V-Pos. /Clock/Phase 57 Wide Mode/DNR/Quick Shoot/ Monitor Speaker Output » Due to the type of signal and its frequency, some items are not selectable and grayed out. NOTE: » "C. M. S. " is the only picture adjustment item which can be used with PC (digital) signals. » "Fine Sync. " (position adjustment etc. ) cannot be used with PC (digital) signals. US 34 Menu Items (Continued) AV input mode menu items INPUT1: AV, Y/C INPUT2: INPUT3: COMPONENT For a table of adjustment ranges for each menu item, please see Appendix3 on page 71. Picture Audio Power control Setup Option 51 Contrast/Black Level/Color/Tint/ Sharpness/ 51 Advanced C. M. S. (H)/(S)/(V) /Color Temp/Black/ 3D-Y/C / Monochrome/Film Mode/ Basic Operation I/P Setting 53 Treble/Bass/Balance 53 53 Brightness Power Management 54 54 55 56 36 56 56 56 56 Control Lock Input Select Position Picture Flip Language INPUT2 Select ID No. Setting Enlarge Panel Protection Cover 54 Lock Item Menu Display/Remote/Buttons/Power/ RS-232C PIN/PIN Clear 54 55 H-Pos. /V-Pos. 57 Wide Mode/Color System/ DNR/Quick Shoot/ Monitor Speaker Output »"INPUT2 Select" is not displayed when the input mode is set to "INPUT2". » Due to the type of signal and its frequency, some items are not selectable and grayed out. NOTE: » If "Underscan" has been selected in "Wide Mode", most picture adjustment items cannot be used (except for some settings in "Advanced"). 35 US Menu Items (Continued) Language setting I The On-Screen Display language can be set to Japanese, English, German, French or Spanish. 1 1 Press to display the menu screen. 2 Press or to select "Setup". MENU [Setup] MENU Picture Audio Power control Setup Control Lock Input Select Position Picture Flip Option [AV] [Normal] [English] [Input] Language Input 2 Select ID No. Setting Enlarge Panel Protection Cover [--] [Off] [Detached] STANDBY/ON INPUT RETURN VOL MENU ENTER ENLARGE WIDE 2 Press or to select "Language", then press ENTER . Power control Setup Control Lock Input Select [AV] Option LCD MONITOR Position Picture Flip Language Input 2 Select ID No. Setting Enlarge Panel Protection Cover [Normal] [English] [Input] [--] [Off] [Detached] 3 Press or language. MENU [ MENU [Setup···Language] to select desired Display language settings. English Deutsch Français Español :Select / RETURN :Back MENU :Exit »The menu screen is now displayed in the language selected. 4 Press screen. MENU to return to normal US 36 PC Operation PC connection 1 One-to-one connection with a PC . . . . . . . Basic operation Connect with RS-232C cross cable between the PC COM port (RS-232C connector) and the RS232C INPUT terminal on the back of monitor. "Rear view To RS-232C INPUT terminal To COM port "PC Basic Operation RS-232C cross cable 2 Daisy chain connection from a single PC. . . . . . . Advanced operation Connect with RS-232C cross cable between the PC COM port (RS-232C connector) and the RS232C INPUT terminal on the back of monitor. They can also be connected as shown below. [Example] PC ID number: 3 ID number: 2 ID number: 4 ID number: 1 Continued on the next page. 39 US PC Operation (Continued) <Commands for ID control> The command examples shown on this page assume the following connection and ID number set up. PC ID number: 1 ID number: 2 ID number: 3 ID number: 4 IDST······A monitor receiving this command sets its own ID number in the parameter field. Example: IDST0001 OK 001 The ID number of this monitor is set to 1. Note After linking monitors, you can automatically assign ID numbers by using the IDST command with the Repeater control (see "Repeater control" on page 42). [Example] PC Set 1 Set 2 Set 3 Set 4 If you connect monitors as shown above, and use the command "IDST001+", ID numbers will be set automatically, as shown below. [Example] PC ID number: 1 ID number: 2 ID number: 3 ID number: 4 IDST001+ WAIT OK 001 OK 002 OK 003 OK 004 ID setting command with repeater control ID = "OK" response from ID number=1 ID = "OK" response from ID number=2 ID = "OK" response from ID number=3 ID = "OK" response from ID number=4 (End) US 40 PC Operation (Continued) IDSL······ The parameter of this command sets the ID number indicating the monitor subject to the next command. Example: IDSL0002 The next command is for the monitor with ID number=2. WAIT Searching for monitor with ID number=2. OK 002 Found monitor with ID number=2 VOLM0030 Set volume of monitor with ID number=2 to 30 WAIT Processing OK 002 OK response from monitor with ID number=2 The IDSL command is VOLM0020 Set volume to 20 effective only once, for the OK 001 The volume of the monitor with ID number=1 immediately succeeding (the one directly connected to the PC) is set to command. IDLK······ The parameter of this command sets the ID number indicating the monitor subject to all subsequent commands. Example: IDLK0002 Following commands are for the monitor whose ID number is "2". WAIT Searching for monitor with ID number=2. [. . . ] (kg) AC120V, 60Hz 181 W 0. 8 W 37-23/64 x 3-29/32 x 22-33/64 (949 x 99. 5 x 572) 41. 9 (19) (without stand) 0°C ­ +40°C 20% ­ +80% I As a part of policy of continuous improvement, SHARP reserves the right to make design and specification changes for product improvement without prior notice. The performance specification figures indicated are nominal values of production units. There may be some deviations from these values in individual units. I The Liquid Crystal panel is a very high technology product with 3, 147, 264 thin film transistors, giving you fine picture details. [. . . ]